Introduction
This manual provides detailed instructions for the safe and effective use of your Aeolus MC-670 Corded Pet Grooming Clipper. Please read all instructions carefully before operating the device and retain this manual for future reference. This clipper is designed for grooming pets, offering a reliable solution for maintaining your pet's coat at home.
Important Safety Instructions
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury. Read all instructions before using this appliance.
- Do not reach for an appliance that has fallen into water. Unplug immediately.
- Do not use while bathing or in a shower.
- Do not place or store appliance where it can fall or be pulled into a tub or sink.
- Except when charging, always unplug this appliance from the electrical outlet immediately after using.
- Unplug this appliance before cleaning, putting on or taking off parts.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged.
- Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to OFF, then remove plug from outlet.
- Do not use this appliance with a damaged or broken blade or comb, as injury may occur.
- Ensure the power cord is not twisted or tangled during use.
- Always ensure the pet is calm and restrained during grooming to prevent injury.
Package Contents
Verify that all items listed below are present in your package:
- Aeolus MC-670 Pet Grooming Clipper
- One 10" Detachable Blade (pre-installed or separate)
- 4 Attachment Combs (3mm, 6mm, 9mm, 12mm)
- Clipper Oil
- Blade Brush
- Owner's Manual
Figure 1: Included accessories with the Aeolus MC-670 Pet Grooming Clipper.
Figure 2: Overview of all items included in the Aeolus MC-670 Pet Grooming Clipper package.
Setup Instructions
- Unpack the Clipper: Carefully remove all components from the packaging. Inspect the clipper and accessories for any signs of damage.
- Blade Installation/Check: The clipper comes with a 10" detachable blade. Ensure it is securely attached. To attach, align the blade with the clipper head and push until it clicks into place. To detach, press the release button (if present, usually on the back of the clipper head) and pull the blade forward.
- Attach a Comb Guide: Select the desired attachment comb (3mm, 6mm, 9mm, or 12mm) based on the desired hair length. Slide the comb onto the blade until it securely snaps into position. Ensure it is firmly seated to prevent it from coming off during grooming.
- Initial Oiling: Before first use, apply a few drops of the provided clipper oil to the blades. Turn the clipper on for a few seconds to distribute the oil evenly. This ensures smooth operation and prolongs blade life.
- Power Connection: Plug the clipper's power cord into a standard electrical outlet (240V/50-60Hz).
Figure 3: Side view of the clipper, highlighting the blade and power switch.
Figure 4: Close-up of the detachable ceramic edge blade.
Operating Instructions
Follow these steps for effective and safe pet grooming:
- Prepare the Pet: Ensure your pet's coat is clean, dry, and free of tangles or mats. Brush the coat thoroughly before clipping.
- Turn On the Clipper: Locate the power switch on the clipper body (typically a red button or slide switch) and slide it to the "ON" position.
- Grooming Technique:
- Hold the clipper firmly with the blade flat against the pet's coat.
- Move the clipper in the direction of hair growth for a natural finish, or against the direction for a shorter cut (use caution and appropriate comb guide).
- Use smooth, even strokes. Avoid pressing too hard, as this can cause irritation or blade overheating.
- Regularly check the blades for hair buildup and clear as needed using the blade brush.
- Take breaks if the clipper or blades become warm to the touch.
- Finishing: Once grooming is complete, turn off the clipper by sliding the power switch to the "OFF" position. Unplug the clipper from the electrical outlet.
Figure 5: Front view of the clipper with the power switch visible.
Maintenance
Proper maintenance ensures the longevity and performance of your clipper.
- Cleaning Blades: After each use, detach the blade and use the provided blade brush to remove all hair and debris from between the blades.
- Oiling Blades: Apply 2-3 drops of clipper oil to the top and sides of the blade teeth after each cleaning. Run the clipper for a few seconds to distribute the oil. This reduces friction, prevents rust, and keeps blades sharp.
- Cleaning the Clipper Body: Wipe the clipper body with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure no water enters the motor housing.
- Storage: Store the clipper and its accessories in a clean, dry place, away from direct sunlight and extreme temperatures. Keep the power cord neatly coiled.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clipper does not turn on. | Not plugged in; power outlet issue; damaged cord/switch. | Ensure clipper is securely plugged into a working outlet. Check for visible damage to the cord or switch. If damaged, discontinue use and contact support. |
| Clipper pulls hair or cuts poorly. | Blades are dull; blades are dirty/clogged; insufficient oil; comb guide not properly attached. | Clean and oil the blades thoroughly. Ensure the comb guide is securely attached. If blades are dull, they may need replacement. |
| Clipper becomes hot during use. | Prolonged use; blades are dirty/un-oiled; motor strain. | Turn off the clipper and allow it to cool down. Clean and oil the blades. Ensure the pet's coat is free of mats to reduce motor strain. |
| Excessive vibration or noise. | Blade not properly seated; internal issue. | Ensure the blade is correctly attached and secured. If the issue persists, discontinue use and contact support. |
Specifications
- Model: MC-670
- Brand: Aeolus
- Power Input: 240V/50-60Hz
- Motor: 12V DC
- Construction Material: Premium Polymer Plastic
- Blade Material: Stainless Steel (Ceramic Edge)
- Special Feature: Corded Operation
- Product Dimensions (L x W x H): 28 x 13.5 x 12.5 cm
- Net Quantity: 1.00 Count
Figure 6: Technical specifications of the Aeolus MC-670 Pet Grooming Clipper.
Warranty and Support
Your Aeolus MC-670 Pet Grooming Clipper comes with a 6-month warranty from the date of purchase, covering manufacturing defects. Please retain your purchase receipt as proof of purchase.
Figure 7: Warranty information for the Aeolus MC-670 Pet Grooming Clipper.
For warranty claims, technical assistance, or any product-related inquiries, please contact the manufacturer or authorized service center. Refer to the contact information provided on the product packaging or the official Aeolus website.
