Introduction
This manual provides comprehensive instructions for the proper setup, operation, and maintenance of your Breitling Super Chronomat B01 44 UTC Men's Watch, model AB0136251B1A2. Please read this manual thoroughly before using your watch to ensure optimal performance and longevity.
Figure 1: Front view of the Breitling Super Chronomat B01 44 UTC Men's Watch. This image displays the watch face with its black dial, three subdials, and a stainless steel bracelet. The bezel features a tachymeter scale and rider tabs.
Setup
Unboxing and Initial Inspection
Carefully remove the watch from its packaging. Inspect the watch for any visible damage or defects. Ensure all components, including the watch, warranty card, and instruction booklet, are present.
Figure 2: The Breitling watch box. This image shows the dark blue fabric-covered box with the Breitling logo, designed to protect and store the watch.
Setting the Time and Date
- Unscrew the Crown: Gently unscrew the crown (located on the right side of the watch case) counter-clockwise until it pops out to position 1.
- Set the Date (if applicable): Pull the crown out to position 2. Turn the crown clockwise or counter-clockwise to adjust the date. Push the crown back to position 1.
- Set the Time: Pull the crown out to position 3. The seconds hand will stop. Turn the crown to set the hour and minute hands to the desired time. To ensure accuracy, synchronize with a reliable time source.
- Screw Down the Crown: Once the time is set, push the crown back to position 1 and screw it clockwise firmly against the case to ensure water resistance.
Adjusting the Bracelet
The stainless steel bracelet can be adjusted by adding or removing links. This procedure should ideally be performed by a qualified watchmaker or an authorized Breitling service center to prevent damage to the bracelet or watch.
Operating the Chronograph and UTC Function
Chronograph Operation
The Super Chronomat B01 features a precise chronograph function for measuring elapsed time.
- Start: Press the upper push-piece (at 2 o'clock) to start the chronograph. The large central seconds hand will begin to move.
- Stop: Press the upper push-piece again to stop the chronograph. The elapsed time can be read from the central seconds hand and the chronograph subdials (30-minute counter at 3 o'clock, 12-hour counter at 6 o'clock).
- Reset: Press the lower push-piece (at 4 o'clock) to reset the chronograph hands to zero. This can only be done when the chronograph is stopped.
UTC (Universal Time Coordinated) Function
The integrated UTC module allows for the display of a second time zone. The UTC module is located on the lower part of the bracelet.
- Setting the UTC Time: The UTC module has its own crown. Unscrew and pull out the crown of the UTC module. Turn the crown to set the desired second time zone. Push in and screw down the crown to secure.
- Reading the UTC Time: The UTC module displays a 24-hour time, making it easy to distinguish between AM and PM for the second time zone.
Maintenance
Cleaning Your Watch
Regular cleaning helps maintain the appearance and integrity of your watch. Use a soft, damp cloth to wipe the case and bracelet. For more thorough cleaning, especially after exposure to saltwater, rinse the watch under lukewarm tap water with the crown fully screwed down, then dry with a soft cloth.
Water Resistance
Your Breitling Super Chronomat B01 44 UTC is water-resistant. However, it is crucial to ensure the crown and push-pieces are fully screwed down before any contact with water. Avoid operating the crown or push-pieces underwater.
Servicing
For optimal performance and longevity, it is recommended to have your Breitling watch serviced by an authorized Breitling service center every 3-5 years. Regular servicing includes checking the movement, replacing seals, and ensuring water resistance.
Figure 3: Rear view of the Breitling Super Chronomat B01 44 UTC Men's Watch. This image showcases the transparent case back, revealing the intricate automatic movement of the watch.
Troubleshooting
Watch Not Running
- Automatic Movement: This watch is equipped with an automatic movement, which is powered by the motion of your wrist. If the watch has stopped, it may need to be wound manually. Gently turn the crown clockwise (with the crown screwed down) about 40 times to provide an initial power reserve.
- Insufficient Wear: If you do not wear the watch regularly, or if your activity level is low, the power reserve may deplete. Consider using a watch winder if the watch is not worn daily.
Date Not Changing
- "Danger Zone": Avoid setting the date between 9 PM and 3 AM, as this is when the date change mechanism is engaged and manual adjustment can damage the movement.
- Incorrect Setting: Ensure the crown is pulled out to the correct position for date adjustment.
Chronograph Hands Not Resetting to Zero
If the chronograph hands do not reset precisely to zero, a recalibration may be necessary. This typically requires professional adjustment by an authorized service center.
Specifications
| Feature | Detail |
|---|---|
| Model Number | AB0136251B1A2 |
| Movement | Breitling Manufacture Caliber B01 (Self-winding mechanical) |
| Case Material | Stainless Steel |
| Case Diameter | 44 mm |
| Water Resistance | 200 meters (660 feet) |
| Crystal | Cambered sapphire, glareproofed on both sides |
| Power Reserve | Approximately 70 hours |
| Chronograph | 1/4th second, 30-minute, 12-hour |
| Additional Function | UTC (Universal Time Coordinated) module |
| Clasp Type | Buckle |
Warranty and Support
Warranty Information
Breitling watches are covered by a manufacturer's warranty against defects in materials and workmanship. The specific duration and terms of the warranty are provided with your watch's warranty card. Please retain your proof of purchase and warranty card for any warranty claims.
Customer Support
For technical assistance, service, or warranty inquiries, please contact an authorized Breitling service center or visit the official Breitling website for a list of service locations. Visit Breitling Official Website
