FINGERS FR-630 UPS Power Supply User Manual

1. Important Safety Instructions

Please read and understand all safety instructions before installing or operating your FINGERS FR-630 UPS. Keep this manual for future reference.

• Do not open the UPS casing. There are no user-serviceable parts inside.
• Do not expose the UPS to rain, moisture, or direct sunlight.
• Ensure the UPS is connected to a grounded power outlet.
• Do not block ventilation openings.
• Avoid placing the UPS near heat sources or in areas with excessive dust.
• Disconnect the UPS from the power source before cleaning.

2. Product Overview

The FINGERS FR-630 is a Line Interactive Uninterrupted Power Supply (UPS) designed to provide reliable power protection for your electronic devices. It features Automatic Voltage Regulation (AVR) and a fast recharge capability.

Figure 2.1: FINGERS FR-630 UPS highlighting 33% faster recharge capability.

Key Features:

• 600VA/360W Capacity: Provides sufficient power backup for various devices.
• 33% Faster Recharge: Ensures quicker battery recovery compared to standard UPS units.
• AVR Stabilization: Boost and Buck Automatic Voltage Regulation stabilizes fluctuating voltages.
• Smart Microprocessor Control: For reliable performance and precise voltage monitoring.
• Auto Restart: Automatically restarts connected appliances after AC power returns.
• Cold Start Mode: Allows the UPS to power on without AC input.
• Generator/Inverter Compatible: Designed to work seamlessly with generator and inverter power sources.

Figure 2.2: Front view of the FINGERS FR-630 UPS, indicating its 600VA/360W capacity.

Figure 2.3: Side view of the FINGERS FR-630 UPS, highlighting its compatibility with generators and inverters.

3. Setup and Installation

1. Unpacking: Carefully remove the UPS from its packaging. Inspect for any shipping damage.
2. Placement: Place the UPS on a flat, stable surface in a well-ventilated area, away from direct sunlight, heat sources, and excessive moisture. Ensure adequate clearance around the ventilation openings.
3. Initial Charge: Before first use, connect the UPS to a standard AC power outlet for at least 8 hours to ensure the battery is fully charged. The UPS will charge whether it is turned on or off.
4. Connecting Devices: Plug your computer, monitor, router, or other critical electronic devices into the output sockets on the rear of the UPS. Do not connect laser printers or other high-surge devices to the UPS output, as this may overload the unit.
5. Power Connection: Plug the UPS power cord into a grounded wall outlet.

4. Operation

Turning On/Off:

• To Turn On: Press and hold the power button for approximately 3 seconds until you hear a beep and the indicators light up.
• To Turn Off: Press and hold the power button for approximately 3 seconds until the indicators turn off.

Indicator Lights:

Automatic Voltage Regulation (AVR):

The UPS automatically detects and corrects minor voltage fluctuations (sags or surges) without switching to battery power, protecting your devices and extending battery life.

Cold Start Function:

The UPS can be powered on using its internal battery even when there is no AC input. To activate, ensure the UPS is off, then press and hold the power button until the unit starts.

5. Maintenance

• Battery Care: To maximize battery life, ensure the UPS is connected to AC power and fully charged at all times. If the UPS is stored for an extended period, recharge it every three months.
• Cleaning: Use a soft, dry cloth to clean the exterior of the UPS. Do not use liquid or aerosol cleaners.
• Ventilation: Regularly check that the ventilation openings are clear of dust and obstructions to prevent overheating.
• Battery Replacement: The internal battery is a sealed lead-acid type. Battery replacement should only be performed by qualified service personnel.

6. Troubleshooting

7. Specifications

8. Warranty and Support

Warranty: This FINGERS FR-630 UPS Power Supply comes with a 1 Year Warranty from the date of purchase. Please retain your purchase receipt as proof of warranty.

The warranty covers manufacturing defects. It does not cover damage caused by misuse, accidents, unauthorized modifications, or improper installation.

Support: For technical assistance, troubleshooting, or warranty claims, please contact FINGERS customer support.

• Manufacturer: Dynamic Conglomerate Pvt. Ltd.
• Address: 329/330, GIDC Phase II, Near Sardar Chowk, Vapi, Valsad, Gujarat, 396195, India.
• Please refer to the official FINGERS website or your purchase documentation for the most current contact information.