TIGERSGATE TIGERSGATE-PRE-26

Download PDF
Contents

TIGERSGATE PREWIRED 1.5" Fat Ape Hanger Handlebar

Model: TIGERSGATE-PRE-26 | Rise: 12 Inches | Compatibility: 2016-2023 Harley Road Glide Models

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your TIGERSGATE PREWIRED 1.5" Fat Ape Hanger Handlebar. Please read this manual thoroughly before installation to ensure proper fitment and safe operation. Professional installation is recommended.

TIGERSGATE 12-inch Chrome Prewired Fat Ape Hanger Handlebar

Image 1.1: TIGERSGATE 12-inch Chrome Prewired Fat Ape Hanger Handlebar.

2. Compatibility

This handlebar is designed for the following motorcycle models:

  • 2016-2023 Harley-Davidson Touring Road Glide (FLTR)
  • 2016-2023 Harley-Davidson Road Glide Special (FLTRXS)
  • 2016-2023 Harley-Davidson Road Glide Custom (FLTRX)

Important Note for CVO & Ultra Models: For CVO and Ultra Road Glide models, the alignment pin hole on the left side of the factory bar bottom may differ from this handlebar. If you wish to use this handlebar, you may need to use pliers to remove the alignment pin from the risers or drill an additional hole on the left side of the handlebar bottom to accommodate it.

3. Package Contents

Verify that all items are present in the package:

  • 1 x Pre-wired Handlebar (12" Rise, Chrome)
  • 1 x Plug-and-Play CAN-Bus Switch Control Harness
  • 1 x Throttle By Wire (TBW) Harness (without plugs)
  • 1 x Easy Installation Tools Kit

4. Features

4.1 Pre-wired Design

The TIGERSGATE handlebar comes pre-wired with CAN-Bus switch control wires and a Throttle By Wire (TBW) harness to simplify the wiring process during installation.

Comparison of pre-wired and non-pre-wired handlebars

Image 4.1: Illustration of the pre-wired CAN-Bus control wires and TBW harness.

4.2 High-Strength Material

Constructed from high-strength SAPH440 steel, these handlebars offer enhanced durability, toughness, and safety compared to standard iron alternatives. The surface features a multi-layer chrome plating for corrosion resistance and a polished finish.

Diagram showing layers of chrome plating on steel handlebar

Image 4.2: Cross-section illustrating the durable SAPH440 steel base and multi-layer chrome plating.

4.3 Design Elements

  • Castle-Shaped End: The right side of the handlebar features a pre-cut castle-shaped end, designed for easier installation and a clean aesthetic.
  • Pre-drilled Wire Holes: Smooth, pre-drilled holes facilitate wire threading and protect wires from abrasion.
  • Anti-slip Knurling: Diamond-patterned knurling provides enhanced grip control for secure handling.
  • Laser Cutting: Precision laser cutting ensures clean, burr-free edges and consistent quality.
Close-up images of handlebar features: meathook bend, anti-slip knurling, TIG welding, and laser cutting

Image 4.3: Detailed view of the handlebar's design features, including the meathook bend, anti-slip knurling, and precision manufacturing.

5. Installation

Installation of handlebars requires mechanical aptitude and specialized tools. If you are not confident in your ability to perform this installation, it is recommended to seek assistance from a qualified motorcycle technician.

5.1 General Steps (Overview)

  1. Safely secure the motorcycle.
  2. Remove existing handlebars and controls.
  3. Carefully route the pre-wired harnesses through the new TIGERSGATE handlebar.
  4. Mount the new handlebar onto the risers, ensuring proper alignment.
  5. Install controls and connect wiring as per the instructions below.
  6. Verify all connections and test functionality before riding.

5.2 Wiring Instructions for Throttle By Wire (TBW)

The TBW harness is pre-routed but does not include plugs. There are two primary routing plans:

  • Plan 1 (Cutting and Splicing): For some motorcycles, the handlebar's internal space may not be sufficient for the total length of existing and pre-wired TBW wires. In this scenario, you may need to cut your existing TBW wires and the pre-wired TBW wires, then connect them using appropriate splicing techniques. Ensure secure and insulated connections.
  • Plan 2 (Rerouting Existing Wires): If you prefer not to cut your existing wires, you will need to carefully pull the pre-wired TBW wire out of the handlebar and reroute your original TBW wire through the new handlebar. This process can be challenging and may require significant patience.

Assistance: For detailed TBW wire connection instructions, please contact TIGERSGATE customer support.

5.3 CVO & Ultra Alignment Pin Adjustment

As noted in the compatibility section, CVO and Ultra models may require modification to the alignment pin. Use pliers to remove the alignment pin from your risers, or carefully drill an additional hole on the left side of the handlebar bottom to match your motorcycle's setup.

6. Specifications

SpecificationDetail
Rise (Height)12 inches (bottom-to-grip end)
Bar Diameter1.5 inches
Clamp Area Diameter1.25 inches
Clamp Area Length5.4 inches
Knurl Center3.5 inches
Base Width13.5 inches
MaterialHigh-Strength SAPH440 Steel
FinishChrome Plated
Item Weight10.87 pounds
Product Dimensions37 x 12 x 0.1 inches (approximate)
Manufacturer Part NumberTIGERSGATE-PRE-26
Diagram showing handlebar dimensions including rise, bar diameter, clamp area, knurl center, and base width

Image 6.1: Detailed specifications diagram of the handlebar dimensions.

7. Maintenance

To ensure the longevity and appearance of your TIGERSGATE handlebar, follow these maintenance guidelines:

  • Regular Cleaning: Clean the chrome surface regularly with a soft cloth and a mild, non-abrasive chrome cleaner. Avoid harsh chemicals or abrasive materials that can damage the finish.
  • Inspection: Periodically inspect the handlebar for any signs of damage, corrosion, or loose connections. Check all bolts and fasteners for proper torque.
  • Wiring Check: Ensure all wiring connections remain secure and free from pinching or fraying.
  • Storage: When not in use, store your motorcycle in a dry environment to prevent moisture-related corrosion.

8. Troubleshooting

This section addresses common issues that may arise during or after installation.

8.1 Wiring Difficulties

  • Tight Fit for Wires: If routing existing TBW wires is difficult, consider the two plans outlined in Section 5.2. Ensure wires are not pinched or damaged during routing.
  • No Pull String: Some users have noted that a pull string for the TBW wire may not be included. If this is the case, alternative methods for wire routing (e.g., using a guide wire) may be necessary.
  • Incorrect TBW Connection: If the throttle does not function correctly after wiring, double-check all connections against the motorcycle's wiring diagram. Contact TIGERSGATE support for specific TBW wiring instructions if needed.

8.2 Alignment Pin Issues (CVO/Ultra)

If the handlebar does not sit flush due to the alignment pin, refer to the instructions in Section 5.3 for modifying the risers or the handlebar.

8.3 Poor Welds/Craftsmanship

While TIGERSGATE aims for high quality, if you observe any manufacturing defects such as poor welds or finish issues upon inspection, contact TIGERSGATE customer service immediately for assistance.

9.1 Customer Support

For any questions, technical assistance, or concerns regarding your TIGERSGATE handlebar, please contact TIGERSGATE customer service. Our team of engineers is available to provide support.

You can find TIGERSGATE's contact information in the 'About Seller Profile' section on the product's retail page.

PLEASE NOTE:

This is an brand new aftermarket modification item by TIGERSGATE, not an OEM part. It will fit the models listed but modification may or may not be required. This item is intended for professional installation. Please check compatibility before purchasing. Thank you for your understanding.

© 2023 TIGERSGATE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.