1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your LUTEC 3200LM Dual-Head Motion Activated Flood Light. Please read this manual thoroughly before installation and use to ensure proper function and safety. This flood light is designed for outdoor use, offering motion-activated security lighting with adjustable heads and various operational modes.
2. Safety Information
- Electrical Safety: Installation must be performed by a qualified electrician or in accordance with local electrical codes. Ensure power is turned off at the circuit breaker before installation, maintenance, or bulb replacement.
- Grounding: This fixture must be properly grounded.
- Bulb Type: For models requiring separate bulbs, use only PAR38 LED, PAR38 incandescent, PAR38 halogen, or PAR38 dimmable CFL bulbs as specified. Do not exceed the maximum wattage rating.
- Heat: Halogen bulbs generate significant heat. Allow the fixture to cool before handling or replacing bulbs. Keep flammable materials away from the light heads.
- Waterproof Rating: The fixture is waterproof for outdoor use. Ensure all connections are sealed properly during installation to maintain this rating.
- Mounting: Mount the fixture securely to a stable surface according to the installation instructions.
3. Package Contents
Verify that all components are present before beginning installation:
- LUTEC Dual-Head Motion Activated Flood Light Fixture
- Mounting Hardware (screws, wire nuts, gasket)
- Instruction Manual
Note: For models requiring separate bulbs, PAR38 bulbs are NOT included and must be purchased separately.
4. Setup and Installation
Follow these steps for safe and proper installation of your flood light.
4.1 Preparation
- Turn off Power: Locate the circuit breaker controlling the outdoor lighting circuit and turn off the power.
- Select Mounting Location: Choose a suitable wall or eave location that provides the desired coverage area and is within reach of existing wiring. The recommended mounting height is 6-10 feet (1.8-3 meters) above the ground.
4.2 Mounting the Fixture
The flood light is designed for surface-mounted installation.
- Attach the mounting bracket to the junction box using the provided screws.
- Feed the electrical wires from the junction box through the center hole of the mounting bracket.
- Connect the wires: Connect the black fixture wire to the black supply wire, the white fixture wire to the white supply wire, and the green/bare copper fixture wire to the ground wire using wire nuts. Ensure connections are secure.
- Carefully tuck the wires into the junction box.
- Align the fixture with the mounting bracket and secure it with the provided screws, ensuring the gasket creates a watertight seal against the mounting surface.
Image 1: Overview of the LUTEC Dual-Head Motion Activated Flood Light. This image displays the two adjustable light heads and the integrated motion sensor, ready for wall mounting.
4.3 Bulb Installation (for Halogen/Incandescent Models)
If your model requires separate bulbs:
- Carefully screw the PAR38 bulbs (up to 150W each, not included) into the sockets of the light heads. Do not overtighten.
- Ensure the bulbs are fully seated.
Image 2: A bronze-colored LUTEC security light mounted on a wall, illustrating the appearance without bulbs installed. This highlights that bulbs are a separate purchase for certain models.
4.4 Power On
Once installation is complete, restore power at the circuit breaker.
5. Operating Instructions
Your LUTEC flood light features adjustable light heads and a motion sensor with customizable settings.
5.1 Adjusting Light Heads
The two light heads can be rotated 360 degrees horizontally and vertically to direct illumination precisely where needed. Loosen the adjustment screws slightly, position the heads, and then tighten the screws to secure them.
Image 3: This image demonstrates the adjustable design of the flood light heads, showing arrows indicating the range of motion for directing light. This feature allows users to customize the illuminated area.
Image 4: Another view of the adjustable design, featuring a bronze-colored fixture. The arrows highlight the flexibility in positioning the light heads and the motion sensor.
5.2 Motion Sensor Operation
The integrated motion sensor detects movement within its sensing range and activates the light. The sensor has a 180-degree sensing angle.
Image 5: Diagram illustrating the motion sensor's 180-degree sensing angle and a maximum range of 20-70 feet. A silhouette of a person walking is shown to demonstrate detection.
Image 6: A similar diagram showing the motion sensor's 180-degree sensing angle and a maximum range of 0-59 feet for the LED version. This visual aids in understanding the sensor's coverage.
6. Motion Sensor Settings
The motion sensor features adjustable controls for sensitivity (distance) and illumination duration (time). These controls are typically located on the underside of the sensor unit.
Image 7: Close-up of the motion sensor controls, showing dials for 'Sensitivity' (L, M, H) and 'Time' (1 MIN, 3 MIN, 10 MIN, TEST). This image helps users identify and adjust the settings.
Image 8: Another close-up of the motion sensor controls, specifically for the LED version, showing 'Distance' (L, M, H, Dusk to Dawn) and 'Time' (1 MIN, 3 MIN, 10 MIN, TEST). This provides specific settings for LED models.
6.1 Sensitivity (Distance) Settings
This dial controls how far the sensor detects motion.
- L (Low): Up to 0-20 ft. (LED) / Up to 20-30 ft. (Halogen)
- M (Medium): Up to 20-39 ft. (LED) / Up to 40-50 ft. (Halogen)
- H (High): Up to 39-59 ft. (LED) / Up to 60-70 ft. (Halogen)
- Dusk to Dawn (LED only): The light will turn on automatically at dusk and turn off at dawn, regardless of motion.
6.2 Time Settings
This dial determines how long the light remains on after motion is detected and stops.
- TEST: For initial setup and aiming the sensor. The light will stay on for a few seconds after detection, regardless of ambient light.
- 1 MIN: Light stays on for approximately 1 minute.
- 3 MIN: Light stays on for approximately 3 minutes.
- 10 MIN: Light stays on for approximately 10 minutes.
6.3 Operating Modes Overview
The combination of settings allows for different operational behaviors:
Image 9: A visual guide to the three main operating modes: Test Mode, Security Mode, and Dusk to Dawn. It shows how the light behaves (OFF, LOW, HIGH) under different ambient light conditions (sun for day, moon for night) and with motion detection.
- Test Mode: Used during installation to verify sensor function and coverage. Light activates for a short duration upon motion, regardless of ambient light.
- Security Mode: Light activates only when motion is detected in low light conditions, staying on for the set time.
- Dusk to Dawn Mode: Light turns on at dusk and off at dawn. For LED models, this can be selected via the distance dial. For Halogen models, this functionality might be integrated with the sensor's light level detection.
7. Maintenance
Regular maintenance ensures optimal performance and longevity of your flood light.
- Cleaning: Periodically clean the light heads and motion sensor lens with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
- Bulb Replacement (for Halogen/Incandescent Models): If a bulb burns out, turn off power at the circuit breaker. Allow the fixture to cool completely. Unscrew the old bulb and replace it with a new PAR38 bulb of the correct wattage (up to 150W).
- Inspection: Annually inspect the wiring and mounting for any signs of wear, damage, or loose connections.
8. Troubleshooting
If your flood light is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Bulb(s) faulty or loose (Halogen/Incandescent). Sensor in 'TEST' mode or incorrect 'Dusk to Dawn' setting. Ambient light too high. | Check circuit breaker. Replace or tighten bulb(s). Adjust sensor settings. Ensure 'Dusk to Dawn' is not selected if motion activation is desired. Wait for darker conditions or adjust sensor sensitivity. |
| Light stays on continuously. | Sensor detecting constant motion. Sensor set to 'Dusk to Dawn' mode. Wiring error. | Adjust sensor angle or sensitivity to avoid unwanted detection. Change sensor setting from 'Dusk to Dawn' if motion activation is desired. Verify wiring connections. |
| Light turns on during the day. | Sensor in 'TEST' mode. Sensor's photocell is obstructed or faulty. | Switch sensor out of 'TEST' mode. Clear any obstructions from the sensor lens. If problem persists, contact support. |
| Motion sensor range is too short/long. | Sensitivity setting incorrect. Obstructions in sensing area. | Adjust the 'Sensitivity' or 'Distance' dial (L, M, H). Remove any objects blocking the sensor's view. |
9. Specifications
| Feature | Specification |
|---|---|
| Brand | LUTEC |
| Model Number | 0fde3b7f-0904-4a5b-9c4b-42a7a822a0f7 |
| Light Source Type | Halogen, LED (compatible with PAR38 bulbs) |
| Brightness | 3200 Lumen (LED), up to 300 Watt (Halogen/Incandescent) |
| Color Temperature | 4000K (LED) |
| Motion Sensor Angle | 180 degrees |
| Motion Sensor Range | Up to 59-70 feet (depending on model/setting) |
| Adjustable Timer | 1, 3, 10 minutes, Test mode |
| Power Source | Corded Electric |
| Voltage | 120 Volts (AC) |
| Indoor/Outdoor Usage | Outdoor |
| Water Resistance Level | Waterproof |
| Mounting Type | Wall Mount |
| Special Features | Dawn-To-Dusk, Dimmable, Motion Sensor, Waterproof |
10. Warranty and Support
Your LUTEC Dual-Head Motion Activated Flood Light is covered by a 3-Year Limited Warranty. This warranty covers defects in materials and workmanship under normal use.
If you encounter any issues or have questions regarding your product, please contact LUTEC customer support. Refer to the product packaging or the official LUTEC website for the most current contact information.
Please retain your proof of purchase for warranty claims.
