Product Overview
This manual provides essential information for the safe and effective use of Norton Reserve A296 6" P120 Grit Aluminum Oxide Non-Vacuum Hook-and-Loop Discs. These discs are designed for various sanding applications, offering durability and consistent performance.
The Norton Reserve A296 sanding disc is a 6-inch diameter abrasive disc featuring P120 grit aluminum oxide. It utilizes a non-vacuum hook-and-loop attachment system, making it suitable for a wide range of sanding tasks. Each package contains 50 discs.
Setup and Installation
Proper installation of the sanding disc is crucial for safety and optimal performance. These discs are designed for use with compatible sanding tools, such as angle grinders, that feature a hook-and-loop backing pad.
- Inspect the Backing Pad: Ensure the hook-and-loop backing pad on your sanding tool is clean and free from debris. A worn or damaged pad may not securely hold the disc.
- Align the Disc: Carefully align the Norton Reserve A296 sanding disc with the backing pad. The hook-and-loop system allows for easy attachment and removal.
- Press Firmly: Press the disc firmly onto the backing pad, starting from the center and working outwards, to ensure full adhesion and prevent wobbling during operation.
- Verify Security: Before starting the tool, gently pull on the edges of the disc to confirm it is securely attached and will not detach during use.
Note: Always refer to your power tool's instruction manual for specific safety guidelines and attachment procedures.
Operating Instructions
The Norton Reserve A296 P120 grit disc is suitable for medium sanding applications. Always wear appropriate personal protective equipment (PPE), including eye protection, hearing protection, and a dust mask, when operating sanding tools.
- Surface Preparation: Ensure the workpiece is clean and securely clamped.
- Start the Tool: Turn on your sanding tool before making contact with the workpiece.
- Apply Even Pressure: Move the sander smoothly and consistently across the surface, applying even, moderate pressure. Avoid excessive pressure, which can lead to premature disc wear or an uneven finish.
- Overlap Passes: Overlap each pass by approximately one-third of the disc's width to ensure uniform material removal.
- Monitor Disc Wear: Replace the disc when it becomes dull or clogged to maintain sanding efficiency and quality.
Grit and Application Guide
The P120 grit of these discs is classified as a medium grit, ideal for preparing surfaces for painting, removing minor imperfections, or light stock removal. Refer to the following guides for optimal application.
Image Description: This image displays two tables. The top table, "Material/Application-to-Product Recommendation Guide," suggests optimal Norton abrasive products (e.g., SG H920, Blaze A995, BlueFire H875P, Gold Reserve A296) for various materials and applications (Heavy-Medium Stock Removal, Light Stock Removal, Finishing). The bottom table, "Application/Grit Recommendation Guide," illustrates the range of grit numbers (from 36 to 1500) and their corresponding applications, from "Coarser (Grinding)" to "Finer (Finishing)," indicating that P120 grit falls within the "Intermediate to Finishing" range.
Maintenance and Storage
Proper maintenance and storage will extend the life and effectiveness of your Norton sanding discs.
- Cleanliness: After use, remove the disc from the sander. If the disc is reusable (e.g., for light clogging), gently clean off any accumulated dust or debris.
- Inspection: Regularly inspect discs for signs of wear, tears, or excessive clogging. Discard damaged or excessively worn discs to prevent poor performance or potential hazards.
- Storage: Store unused discs in their original packaging or a clean, dry environment away from direct sunlight, extreme temperatures, and humidity. This helps prevent degradation of the abrasive and the hook-and-loop backing.
- Handling: Avoid bending or creasing the discs, as this can compromise their structural integrity and lead to uneven sanding.
Troubleshooting Common Issues
| Issue | Possible Cause | Solution |
|---|---|---|
| Poor Sanding Performance / Slow Material Removal |
|
|
| Disc Detaches from Sander |
|
|
| Uneven Sanding Pattern / Swirl Marks |
|
|
Product Specifications
Image Description: A close-up view of a single Norton Reserve A296 6-inch P120 Grit Aluminum Oxide Non-Vacuum Hook-and-Loop Sanding Disc. The disc is circular and features a uniform yellow-orange abrasive surface, indicating its P120 grit texture. The hook-and-loop backing is not visible in this view.
- Product Name: Norton Reserve A296 6" P120 Grit Aluminum Oxide Non-Vacuum Hook-and-Loop Discs
- Model Number: 63642506234
- Brand: Norton
- Disc Diameter: 6 inches
- Grit Type: Aluminum Oxide
- Grit Number: P120 (Medium)
- Attachment System: Hook-and-Loop (Non-Vacuum)
- Compatible Devices: Angle Grinder (and other compatible sanding tools)
- Package Quantity: 50 Pieces
- Product Dimensions: 7.1 x 6.6 x 0.05 inches (packaging); 6"L x 6"W (disc)
- Manufacturer: Norton Abrasives
- Country of Origin: Made in Canada
Warranty and Support
Specific warranty information for this product is not provided in the available documentation. For details regarding product warranty, returns, or technical support, please contact Norton Abrasives directly or refer to their official website.
Manufacturer: Norton Abrasives
For further assistance, please visit the Norton Store on Amazon or the official Norton Abrasives website.
