Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your EMAX Transporter 2 5.8GHz FPV Goggles. Please read this manual thoroughly before using the product to ensure proper function and safety.
Package Contents
Upon opening the package, verify that all components are present:
- 1x EMAX Transporter 2 FPV Goggles
- 1x Micro USB Cable
- 2x Antennas
Image: EMAX Transporter 2 FPV Goggles, Micro USB cable, and two antennas, shown next to the product box.
Setup
1. Charging the Goggles
The Transporter 2 Goggles have a built-in 1300mAh Lithium-ion battery. Before first use, fully charge the device.
- Connect the supplied Micro USB cable to the charging port on the goggles.
- Connect the other end of the USB cable to a 5V--1A USB power source (e.g., computer USB port, wall adapter).
- The charging indicator light will show the charging status. Refer to the device's LED indicators for full charge notification.
2. Attaching Antennas
The goggles utilize two antennas for improved signal reception.
- Carefully screw the two included antennas onto the antenna connectors located on the top of the goggles.
- Ensure they are finger-tight to prevent signal loss.
Image: Front view of the EMAX Transporter 2 FPV Goggles with both antennas securely attached.
3. Detachable DVR Screen
The 4.3" LCD DVR screen is detachable, allowing for flexible use, including with a radio controller.
- To detach, gently slide the screen unit away from the main goggle body.
- To reattach, align the screen unit with the goggle body and slide it back into place until it clicks securely.
Image: The EMAX Transporter 2 FPV Goggles shown with its detachable DVR screen unit separated from the main goggle frame.
4. Adjusting Fit
For optimal comfort and viewing, adjust the goggle strap and focal length.
- Use the 3-way adjustable belt to secure the goggles comfortably on your head.
- Adjust the focal length to achieve a clear image on the screen.
Image: Side view of the EMAX Transporter 2 FPV Goggles, highlighting the adjustable head strap and ergonomic design.
Operating Instructions
1. Powering On/Off
- To power on, press and hold the power button until the screen illuminates.
- To power off, press and hold the power button until the screen turns off.
2. Channel Selection
The goggles operate on the 5.8GHz frequency band with 40 available channels.
- Use the channel selection buttons (refer to the goggle's button layout) to cycle through available frequencies.
- Ensure the goggle's channel matches the video transmitter's channel on your FPV drone for a clear signal.
3. Video Modes
The DVR supports multiple video recording modes.
- Select between VGA, D1, and HD video modes based on your preference and storage needs.
- Access these settings through the goggle's menu system.
4. DVR Functionality
The built-in DVR allows you to record your FPV flights.
- Insert a TF card (up to 32GB max) into the designated slot.
- Recordings are saved in MJPEG format as AVI files.
- Set recording duration (Off/3min/5min/10min) via the menu.
- Ensure the TF card is formatted correctly before use.
5. Compatibility
The EMAX Transporter 2 Goggles are highly compatible with the E8 Radio Transmitter for an integrated FPV experience.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the goggle lenses and exterior. Avoid abrasive materials or harsh chemicals.
- Battery Care: To prolong battery life, avoid fully discharging the battery frequently. Store the goggles with a partial charge (around 50%) if not used for extended periods.
- Storage: Store the goggles in a cool, dry place, away from direct sunlight and extreme temperatures.
- Anti-fogging Fan: The built-in anti-fogging fan helps maintain clear vision. Ensure the fan intake/exhaust is not obstructed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No image on screen | Goggles not powered on; Low battery; Incorrect channel; Video transmitter off/malfunctioning. | Ensure goggles are charged and powered on. Verify channel matches transmitter. Check video transmitter status. |
| Poor image quality/static | Weak signal; Interference; Antennas loose/damaged; Incorrect focal length. | Move closer to drone. Check for sources of interference. Ensure antennas are secure. Adjust focal length. |
| DVR not recording | No TF card; TF card full/corrupted; Incorrect recording settings. | Insert TF card. Format or replace TF card. Check DVR recording settings. |
| Short battery life | Battery not fully charged; Aging battery. | Ensure full charge before use. Battery degradation is normal over time. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | EMAX TRANSPORTER 2 GOGGLES |
| Screen Size | 4.3 inch |
| Screen Resolution | 480x800p |
| Frequency | 5.8GHz (5658MHz-5945MHz), 40 Channels |
| Battery | 1300mAh Lithium-ion battery |
| Working Voltage | 4.2V-3.7V |
| Charging System | Built-in USB 5V--1A linear lithium-ion battery charging system |
| DVR | 32G TF card (max), MJPEG, AVI |
| Video Modes | VGA/D1/HD (Off/3min/5min/10min) |
| Maximum Size (Without antenna - Folded) | 155x100x90mm |
| Weight (With battery) | 398g |
| Product Dimensions | 7.25 x 5.75 x 4 inches |
| Item Weight | 1.45 pounds |
| Compatible Devices | E8 Radio Transmitter |
Warranty Information
EMAX products typically come with a limited manufacturer's warranty. For specific details regarding the warranty period and terms for your Transporter 2 FPV Goggles, please refer to the warranty card included in your product packaging or visit the official EMAX website.
Customer Support
For further assistance, technical support, or to inquire about replacement parts, please visit the official EMAX website or contact their customer service department. Keep your purchase receipt and product serial number handy when contacting support.
Official EMAX Website: www.emax-usa.com
