1. Introduction
This manual provides essential information for the proper use, setup, and maintenance of your Retrospec H1 Ski & Snowboard Helmet. Please read these instructions thoroughly before using the helmet to ensure maximum safety and performance.
2. Safety Information
The Retrospec H1 helmet is designed to provide protection for skiing and snowboarding activities. It features a certified ABS exterior and an EPS foam interior for impact absorption.
- Always ensure the helmet fits snugly and the chin strap is securely fastened before use.
- A helmet cannot protect against all possible impacts. Severe impacts may result in serious injury or death.
- Inspect the helmet for any damage before each use. If the helmet shows signs of damage, or if it has sustained an impact, it must be replaced immediately, even if visible damage is not apparent.
- Do not modify the helmet in any way, as this may compromise its protective capabilities.
- Avoid exposing the helmet to extreme temperatures or harsh chemicals, which can degrade materials.
3. Product Features
- Durable Construction: Certified ABS exterior shell and shock-absorbent EPS foam interior.
- Ventilation System: 10 rectangular vents (6 on top, 2 front, 2 back) designed to regulate temperature and maximize airflow, reducing goggle fogging.
- Goggle Compatibility: Front design accommodates ski goggles, with a dedicated clip on the rear to secure them.
- Comfort Lining: Interior lined with a removable fleece netted cap for moisture-wicking and warmth.
- Removable Earmuffs: Plush, protective earmuffs with zipper pockets for headphones.
- Adjustable Fit: ErgoKnob adjustable dial on the rear for a customized, secure fit.
- Adjustable Chin Strap: Soft-cushioned chin strap to prevent chafing.
- Convertible Design: Easily converts for multi-sport use (snow/ski to skate/bike) by removing the fleece cap and earmuffs and installing included foam padding.
4. Setup and Fitting
4.1. Sizing Guide
To ensure proper fit and maximum protection, measure the circumference of your head just above your eyebrows. Refer to the sizing chart below:
Image: Helmet Sizing Chart
- Small: 51-54 cm
- Medium: 54-58 cm
- Large: 58-61 cm
4.2. Adjusting the Fit
- Place the helmet on your head. It should sit level and cover your forehead.
- Locate the ErgoKnob adjustable dial at the rear of the helmet. Turn the dial clockwise to tighten the fit or counter-clockwise to loosen it. Adjust until the helmet feels snug and secure without causing discomfort. The helmet should not move freely when you shake your head.
- Fasten the chin strap. Adjust the strap so it is snug under your chin, allowing only one or two fingers to fit between the strap and your chin. The strap should not chafe.
4.3. Convertible Configuration (Snow to Skate/Bike)
The H1 helmet can be adapted for different sports:
- To convert for skate/bike use, gently detach the removable earmuffs and the fleece netted cap from the helmet interior.
- Install the foam padding inserts (included with the helmet) into the designated areas inside the helmet for a secure and comfortable fit without the fleece lining.
- Ensure all components are securely fastened before use.
5. Operating Instructions
5.1. Wearing the Helmet
Ensure the helmet is properly adjusted as described in Section 4.2. The helmet should cover your forehead and not obstruct your vision.
Image: Retrospec H1 Helmet, side view.
5.2. Using the Goggle Clip
The helmet features a goggle clip on the rear to secure your ski or snowboard goggles.
- Place your goggles over your eyes.
- Pull the goggle strap around the back of the helmet.
- Slide the goggle strap under the goggle clip to hold it in place.
Image: Goggle clip and adjustable dial detail.
5.3. Airflow Management
The 10 integrated vents facilitate air circulation. Fresh air enters through the front and top vents, pushing out warm, moist air through the rear vents. This design helps maintain a comfortable temperature and reduces goggle fogging.
Image: Airflow diagram.
6. Maintenance
6.1. Cleaning the Helmet
- Use only mild soap and water to clean the helmet's exterior. Avoid harsh chemicals, solvents, or abrasive cleaners.
- The fleece netted cap and earmuffs are removable for cleaning. Hand wash them with mild soap and water, then air dry completely before reattaching.
- Do not machine wash or tumble dry any helmet components.
6.2. Storage
Store the helmet in a cool, dry place away from direct sunlight and extreme temperatures. Do not store heavy objects on top of the helmet, as this can cause damage.
7. Troubleshooting
- Helmet feels loose: Adjust the ErgoKnob dial clockwise to tighten the fit. Ensure the chin strap is also snug.
- Helmet feels too tight/uncomfortable: Adjust the ErgoKnob dial counter-clockwise to loosen the fit. Check if the correct size helmet was selected using the sizing guide.
- Goggles fogging: Ensure the helmet's vents are clear and not obstructed. Proper airflow is crucial for reducing fog. Check that your goggles are compatible and properly seated with the helmet.
- Earmuffs not staying in place: Ensure the earmuffs are correctly snapped or attached to their designated points inside the helmet.
If you experience persistent issues or have concerns about your helmet's performance, contact Retrospec customer support.
8. Specifications
| Brand | Retrospec |
| Model Name | Retrospec H1 Ski & Snowboard Helmet |
| Model Number | 2975 |
| Outer Material | Acrylonitrile Butadiene Styrene (ABS) |
| Inner Material | Expanded Polystyrene (EPS) |
| Item Weight | 1.2 Pounds |
| Special Feature | Adjustable, Lightweight |
| Recommended Uses | Skiing, Snowboarding, Cycling |
| Age Range | Adult |
| UPC | 815725026354 |
9. Warranty and Support
9.1. Warranty Information
This Retrospec H1 helmet is covered by a Limited Warranty. For specific terms and conditions, please refer to the warranty documentation included with your purchase or visit the official Retrospec website.
9.2. Customer Support
For further assistance, product inquiries, or warranty claims, please visit the official Retrospec store or contact their customer service department.
