1. Safety Information
Read all instructions carefully before installation and use. Failure to follow safety guidelines may result in injury or damage to the product or vehicle.
- Ensure the vehicle's ignition is off and the battery is disconnected before beginning installation.
- Wear appropriate personal protective equipment, including safety glasses and gloves.
- Do not modify the product or its components. Use only genuine Can-Am parts and accessories.
- Ensure all wiring connections are secure and properly insulated to prevent short circuits.
- Avoid routing cables near hot engine parts, sharp edges, or moving components.
- Do not operate the audio system at excessively high volumes that may impair your ability to hear traffic or emergency vehicles.
- This product is designed for outdoor use but is not fully waterproof. Avoid direct exposure to high-pressure water jets.
2. Package Contents
Verify all components are present before proceeding with installation.
- Audio System Unit (powered by MTX Audio)
- Mounting Brackets (for handlebar installation)
- Hardware Kit (screws, Allen wrench)
- Wiring Harness (plug-and-play)
- User Manual
Image: View of the Can-Am Ryker Audio System components, including the main unit, wiring, and mounting hardware.
3. Setup & Installation
The Can-Am Ryker System Audio Bluetooth Kit features a plug-and-play design for simplified installation.
3.1 Mounting the Audio System
- Identify the desired mounting location on your vehicle's handlebar.
- Attach the mounting brackets to the handlebar using the provided hardware. Ensure a secure fit.
- Position the audio system unit onto the mounted brackets.
- Secure the audio system unit to the brackets using the appropriate screws and Allen wrench. Adjust the angle for optimal sound projection and rider comfort.
Image: The Can-Am Ryker Audio System securely mounted on the vehicle's handlebars, showing the integrated display and controls.
3.2 Wiring Connections
- Locate the vehicle's battery. Ensure the ignition is off.
- Connect the red wire from the audio system's wiring harness to the positive (+) terminal of the battery.
- Connect the black wire from the audio system's wiring harness to the negative (-) terminal of the battery.
- Route the wiring harness neatly and securely, away from moving parts, heat sources, and sharp edges, using zip ties if necessary.
- Connect the main power connector from the wiring harness to the audio system unit.
Video: A user demonstrates the installation of a drink holder on a Can-Am Ryker, showing the process of removing screws and attaching accessories. This video is provided by a Seller and is relevant for understanding general accessory installation on the Ryker.
4. Operating Instructions
The audio system is designed for intuitive control. Refer to the unit's display and buttons for navigation.
4.1 Power On/Off
- Press and hold the Power button (usually marked with a power symbol) to turn the unit on or off.
4.2 Volume Adjustment
- Use the Volume Up (+) and Volume Down (-) buttons to adjust the audio output level.
4.3 Bluetooth Pairing
- Ensure the audio system is powered on and in Bluetooth mode (indicated on the display).
- On your mobile device, enable Bluetooth and search for available devices.
- Select "Can-Am Audio" or a similar name from the list of devices to pair.
- Once paired, you can stream audio from your device to the audio system.
4.4 Mode Selection
- Press the Mode button (usually marked with 'M') to cycle through available audio sources (e.g., Bluetooth, FM Radio, USB).
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your audio system.
- Keep the audio system clean by wiping it with a soft, damp cloth. Avoid abrasive cleaners or solvents.
- Periodically check all wiring connections for tightness and signs of wear or corrosion.
- Ensure the mounting hardware remains secure. Tighten any loose screws as needed.
- Protect the unit from extreme temperatures and prolonged direct sunlight when not in use.
6. Troubleshooting
If you encounter issues, refer to the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Loose wiring connection, blown fuse, dead battery. | Check battery connections. Inspect the fuse in the wiring harness. Ensure vehicle battery is charged. |
| No audio output | Volume too low, incorrect source selected, Bluetooth not paired. | Increase volume. Press Mode button to select correct source. Re-pair Bluetooth device. |
| Poor sound quality | Weak Bluetooth signal, interference, damaged speaker. | Move device closer to the unit. Avoid sources of interference. Contact support if speakers are damaged. |
| Bluetooth not connecting | Device out of range, pairing mode not active, previous connection issue. | Ensure device is within 10 meters. Activate Bluetooth pairing mode on unit. Forget device on phone and re-pair. |
7. Specifications
- Model Name: 219401033
- Brand: Can-Am
- Speaker Type: Tweeter
- Recommended Uses: For Music Players
- Compatible Devices: Smartphone
- Connectivity Technology: Bluetooth
- Wireless Communication Technology: Bluetooth
- Bluetooth Range: 10 Meters
- Speaker Maximum Output Power: 120 Watts
- Audio Output Mode: Stereo
- Control Method: Touch
- Power Source: Corded Electric
- Mounting Type: Handlebar Mount
- Color: Black
- Is Waterproof: FALSE
- Product Dimensions: 28 x 15 x 15 inches
- Item Weight: 11.48 pounds
- Manufacturer: BRP
- UPC: 810073133853
8. Warranty & Support
This product comes with a Limited Warranty from the manufacturer, BRP.
- For detailed warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Can-Am website.
- For technical support, troubleshooting assistance, or warranty claims, please contact Can-Am customer service.
Contact Information: Refer to your product packaging or the official Can-Am website for the most up-to-date contact details.
