STERWINS 95fa2673-7eab-4224-9d04-0a58ab06f3d1

Download PDF
Contents

STERWINS 8V Cordless Grass and Shrub Shear User Manual

Model: 95fa2673-7eab-4224-9d04-0a58ab06f3d1

1. Introduction

Thank you for choosing the STERWINS 8V Cordless Grass and Shrub Shear. This versatile tool is designed for efficient trimming of grass, small shrubs, and hedges. Please read this manual carefully before operating the tool to ensure safe and effective use. Keep this manual for future reference.

1.1 Intended Use

The STERWINS 8V Cordless Grass and Shrub Shear is intended for domestic use only, specifically for cutting grass edges, small lawn areas, and shaping small ornamental shrubs and hedges with branches up to 8 mm in diameter. Any other use is considered improper and may lead to hazards.

1.2 Package Contents

  • STERWINS 8V Cordless Grass and Shrub Shear unit
  • Grass trimming blade (8 mm cutting width)
  • Shrub trimming blade (for branches up to 8 mm)
  • Integrated Lithium-ion battery
  • Battery charger
  • Instruction Manual
STERWINS 8V Cordless Grass and Shrub Shear with both grass and shrub blades

Figure 1: The STERWINS 8V Cordless Grass and Shrub Shear with both the grass trimming blade and the shrub trimming blade.

2. Safety Instructions

Always observe basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and personal injury. Read all instructions before operating this product.

2.1 General Safety Warnings

  • Keep work area clear: Cluttered areas invite injuries.
  • Consider work area environment: Do not expose power tools to rain or use them in damp or wet locations. Keep work area well lit.
  • Guard against electric shock: Avoid body contact with earthed or grounded surfaces (e.g., pipes, radiators, ranges, refrigerators).
  • Keep children away: Do not let visitors contact the tool or extension cord. All visitors should be kept away from the work area.
  • Dress properly: Do not wear loose clothing or jewelry. They can be caught in moving parts. Use protective gloves and substantial footwear when working outdoors. Wear protective hair covering to contain long hair.
  • Use safety glasses: Also use a face or dust mask if operation is dusty.
  • Do not overreach: Keep proper footing and balance at all times.
  • Maintain tools with care: Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.
  • Disconnect tools: Disconnect the battery pack from the tool before making any adjustments, changing accessories, or storing the tool.
  • Avoid unintentional starting: Ensure the switch is in the off position before inserting the battery pack.
  • Stay alert: Watch what you are doing. Use common sense. Do not operate tool when you are tired.
  • Check for damaged parts: Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
  • Do not use tool if switch does not turn it on or off.
  • Service: This power tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise, this may result in considerable danger to the user.

2.2 Battery Safety

  • Only use the charger specified by the manufacturer.
  • Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  • When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
  • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

3. Components Overview

Familiarize yourself with the parts of your STERWINS Cordless Grass and Shrub Shear before use.

STERWINS 8V Cordless Grass and Shrub Shear with Grip System and blade details

Figure 2: Overview of the STERWINS 8V Cordless Grass and Shrub Shear, highlighting the Grip System and blade specifications.

  • Main Unit / Handle
  • On/Off Switch
  • Safety Lock Button
  • Battery Charge Indicator
  • Blade Release Button
  • Grass Trimming Blade
  • Shrub Trimming Blade
  • Charging Port
STERWINS 8V Cordless Grass and Shrub Shear with dimensions

Figure 3: Dimensions of the STERWINS 8V Cordless Grass and Shrub Shear (approximately 48 cm long and 12 cm high).

4. Setup

4.1 Charging the Battery

The tool is equipped with an integrated Lithium-ion battery. Before first use, fully charge the battery. The battery charge indicator will show the current charge level.

  1. Ensure the tool is switched off.
  2. Connect the charger to the charging port on the tool.
  3. Plug the charger into a suitable power outlet.
  4. The battery takes approximately 180 minutes (3 hours) to fully charge from empty.
  5. The battery charge indicator will change to show full charge when complete.
  6. Disconnect the charger once charging is complete.

Note: The battery is designed to hold its charge well when not in use, preventing self-discharge.

4.2 Installing/Changing Blades

The STERWINS shear comes with two interchangeable blades: one for grass and one for shrubs. Always ensure the tool is switched off and the safety lock is engaged before changing blades.

  1. Press the blade release button, usually located near the blade attachment point.
  2. Carefully slide the current blade out of its slot.
  3. Select the desired blade (grass or shrub).
  4. Align the new blade with the slot and slide it in until it clicks securely into place. Ensure it is firmly seated.
  5. Gently pull on the blade to confirm it is locked and cannot be easily removed.

5. Operating Instructions

5.1 Starting and Stopping the Tool

  1. To start: Press and hold the safety lock button, then press the On/Off switch. Release the safety lock button once the tool starts.
  2. To stop: Release the On/Off switch.

The tool provides approximately 40 minutes of continuous operation on a full charge.

5.2 Cutting Techniques

Always wear appropriate personal protective equipment, including safety glasses and gloves, when operating the shear.

5.2.1 Grass Trimming

  • Attach the grass trimming blade.
  • Hold the tool firmly and at a slight angle to the ground.
  • Move the shear steadily along the edge of the lawn or desired area.
  • Avoid contact with hard objects like stones or metal, which can damage the blade.

5.2.2 Shrub and Hedge Trimming

  • Attach the shrub trimming blade.
  • Hold the tool with both hands for better control, if necessary.
  • Work slowly and deliberately, shaping the shrub as desired.
  • Do not attempt to cut branches thicker than 8 mm.
  • Clear away cut material regularly to maintain visibility.
Person using STERWINS 8V Cordless Grass and Shrub Shear to trim a small shrub

Figure 4: The STERWINS shear in use, demonstrating its application for shaping small shrubs.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your STERWINS shear. Always ensure the tool is switched off and the battery is disconnected (if removable) before performing any maintenance.

6.1 Cleaning

  • After each use, clean the blades and the tool body.
  • Use a brush or cloth to remove grass clippings, leaves, and debris.
  • Do not use water or cleaning solvents directly on the electrical components.
  • Wipe the blades with a lightly oiled cloth to prevent rust.

6.2 Blade Care

  • Keep blades sharp for best cutting performance. Dull blades can strain the motor and lead to poor results.
  • If blades become dull or damaged, they can be sharpened by a professional or replaced with genuine STERWINS replacement blades.
  • Regularly check blades for any signs of damage or wear.

6.3 Storage

  • Store the tool in a dry, secure place, out of reach of children.
  • Ensure the battery is partially charged (not fully depleted or fully charged for long-term storage) if storing for extended periods.
  • Store the blades with their protective covers on to prevent accidental injury and protect the blades.

7. Troubleshooting

This section provides solutions to common problems you might encounter with your STERWINS shear. If the problem persists, contact customer support.

ProblemPossible CauseSolution
Tool does not start.Battery is depleted.
Safety lock button not pressed.
Blade is jammed.
Charge the battery.
Press the safety lock button before the On/Off switch.
Clear any obstructions from the blade area.
Poor cutting performance.Blades are dull or damaged.
Battery is low.
Attempting to cut material too thick.
Sharpen or replace blades.
Recharge the battery.
Do not cut material thicker than 8 mm.
Tool stops during operation.Battery is depleted.
Overload protection activated.
Recharge the battery.
Reduce cutting load. Allow tool to cool down before restarting.
Blade difficult to change.Debris in blade slot.
Blade release button not fully pressed.
Clean the blade slot.
Ensure the blade release button is fully depressed.

8. Specifications

FeatureDetail
Model Number95fa2673-7eab-4224-9d04-0a58ab06f3d1
BrandSTERWINS
ManufacturerADEO
Power SourceBattery powered (8V)
Battery TypeLithium-ion
Charging TimeApprox. 180 minutes (3 hours)
Operating Time (Full Charge)Approx. 40 minutes
Grass Blade Cutting Width8 mm
Shrub Blade Max. Cutting Diameter8 mm
Blade MaterialSteel
Product Dimensions (L x W x H)Approx. 48 x 31 x 12 cm

9. Warranty and Support

For warranty information, technical support, or to order replacement parts, please contact your retailer or the manufacturer's customer service. Keep your proof of purchase for any warranty claims.

Manufacturer: ADEO

For further assistance, please visit the STERWINS brand page on Amazon or consult the official ADEO website.

© 2024 STERWINS. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.