Dayton Audio KAB-23

Download PDF
Contents

Dayton Audio KAB-23 aptX HD Bluetooth 5.0 Receiver Audio Amplifier Board User Manual

Model: KAB-23

1. Introduction

The Dayton Audio KAB-23 is a versatile Bluetooth 5.0 receiver board designed for audio projects. It features aptX HD support for high-quality audio streaming and includes a built-in 2 x 3W amplifier, making it suitable for small audio applications. Its wide 5 to 21 VDC input voltage range offers flexibility for various power sources.

2. Key Features

  • High-quality audio performance with Bluetooth 5.0.
  • Supports audio formats: aptX, aptX HD, aptX LL, SBC, and AAC.
  • Wide operating voltage range: 5 to 21 VDC.
  • Integrated 2 x 3W amplifier for small audio projects.
  • Low power consumption: 50 mA working, 10 mA quiescent.
  • Plug-N-Play JST type connectors for simplified installation.
  • High receive sensitivity with RF power up to 9 dBm and -90 dBm.
  • Stable wireless connectivity up to 15m (50ft).
  • On-board antenna and external antenna jack for flexible mounting.
  • PCM5121 DAC chip for digital to analog conversion.

3. Package Contents

The KAB-23 board typically includes the following components:

  • Dayton Audio KAB-23 Amplifier Board
  • Wire harness for external Bluetooth LED
  • Wire harness for 3.5mm line out
  • Wire harness for Bluetooth reset switch
  • Wire harness for stereo speaker connection (if using built-in amp)
  • 4-pin wire harness for Dayton Audio LBB battery boards
  • Optional: External rubber antenna (sold separately)
Dayton Audio KAB-23 accessory cables

Figure 3.1: Included wire harnesses for the KAB-23 board. These facilitate connections for LED indicators, line out, reset switch, speakers, and battery boards.

4. Board Layout and Connections

Familiarize yourself with the various connectors and components on the KAB-23 board before proceeding with installation.

Top-down view of Dayton Audio KAB-23 board with labeled components

Figure 4.1: Top-down view of the KAB-23 board, showing the layout of components, connectors, and output jacks. Key components include the Bluetooth module, amplifier chips, DAC, and various JST connectors.

Angled view of Dayton Audio KAB-23 board

Figure 4.2: Angled view of the KAB-23 board, highlighting the RCA and 3.5mm output jacks, power input, and various JST connectors for external components.

Bottom view of Dayton Audio KAB-23 board

Figure 4.3: Bottom view of the KAB-23 board, showing the solder points and traces, including the "KAB-23" model designation and Dayton Audio logo.

5. Setup and Installation

Follow these steps for proper installation of your KAB-23 board. Ensure all connections are secure before applying power.

  1. Power Connection: Connect a 5 to 21 VDC power supply to the designated power input connector. Use the appropriate wire harness. Ensure correct polarity.
  2. Speaker Connection (Optional): If utilizing the built-in 2 x 3W amplifier, connect your stereo speakers (4-8 ohms impedance) to the speaker output JST connector using the provided wire harness.
  3. Line Out Connection: For connecting to an external amplifier or receiver, use the 3.5mm line out or RCA jacks. The 3.5mm line out can be connected via its dedicated wire harness.
  4. Bluetooth LED and Reset Switch: Connect the external Bluetooth LED and reset switch using their respective wire harnesses to the corresponding JST connectors on the board.
  5. Battery Board Connection (Optional): For portable applications, connect a Dayton Audio LBB battery board using the 4-pin wire harness.
  6. External Antenna (Optional): If mounting the KAB-23 in a metal enclosure, connect an external rubber antenna (sold separately) to the on-board external antenna jack for improved signal reception.
  7. DAC Switch: The board features a DAC switch. If you are using only the speaker outputs and wish to conserve power, you can switch the DAC to the "off" position.

Caution:

  • Always ensure power is disconnected before making or changing any connections.
  • When unplugging JST connectors, exercise caution to avoid damaging the connectors or the board.

6. Operation

Once the KAB-23 board is properly installed and powered, follow these steps to operate it:

  1. Power On: Apply power to the KAB-23 board. The Bluetooth LED (if connected) should illuminate, indicating it is ready for pairing.
  2. Bluetooth Pairing:
    • On your Bluetooth-enabled device (e.g., smartphone, tablet), navigate to the Bluetooth settings.
    • Scan for available devices. The KAB-23 should appear as "Dayton Audio KAB-23" or similar.
    • Select the KAB-23 to initiate pairing. A confirmation tone or LED change may indicate successful pairing.
  3. Audio Playback: Once paired, begin playing audio from your device. The sound will be transmitted wirelessly to the KAB-23 and output through the connected speakers or line out.
  4. Bluetooth Reset: If you need to clear the current Bluetooth connection or initiate a new pairing, press the connected Bluetooth reset switch.

7. Maintenance

The Dayton Audio KAB-23 board requires minimal maintenance. Observe the following guidelines:

  • Keep the board clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the board to moisture, extreme temperatures, or direct sunlight.
  • Ensure adequate ventilation if enclosed to prevent overheating.
  • Do not attempt to modify the board, as this may void the warranty and cause damage.

8. Troubleshooting

If you encounter issues with your KAB-23 board, refer to the following common problems and solutions:

  • No Power:
    • Verify the power supply is connected correctly and providing 5-21 VDC.
    • Check all power connections for secure contact and correct polarity.
  • Cannot Pair Bluetooth:
    • Ensure the KAB-23 is powered on and within range (up to 15m/50ft) of your device.
    • Try resetting the Bluetooth connection by pressing the reset switch.
    • Clear the KAB-23 from your device's Bluetooth history and attempt to pair again.
    • Ensure no other device is currently paired with the KAB-23.
  • No Audio Output:
    • Check speaker or line out connections for proper wiring and secure contact.
    • Verify the volume on your source device and any connected external amplifier is not muted or too low.
    • Ensure the KAB-23 is successfully paired and receiving audio from your device.
    • If using the built-in amplifier, confirm speakers are 4-8 ohms impedance.
  • Poor Audio Quality / Intermittent Connection:
    • Reduce the distance between your device and the KAB-23.
    • Remove any obstacles (especially metal) between the device and the board.
    • Ensure the external antenna (if used) is properly connected and positioned.
    • Minimize interference from other wireless devices.

9. Specifications

FeatureSpecification
Model NumberKAB-23
Bluetooth Version5.0
Supported Audio FormatsaptX, aptX HD, aptX LL, SBC, AAC
Power Output (w/ 12 VDC)2 x 3W @ 4 ohms
Amplifier SNR88.9 dB
DAC SNR98.6 dB
Max Line Output0.9Vrms
Frequency Response20 to 20,000 Hz (±0.8 dB)
Speaker Impedance4-8 ohms
Working Voltage5 to 21 VDC
Current Draw (Amplifier)Up to 700mA
Current Draw (No Speaker Output)50mA
Idle Current Draw (Bluetooth Connected)10mA
Audio Output DistortionLess than 0.5%
Dimensions (L x W x H)3" x 2" x 0.75" (Board only)
Product Dimensions (Overall)4 x 2.75 x 1.25 inches
Item Weight3.2 ounces

10. Warranty and Support

Dayton Audio products are designed for reliability and performance. This product comes with a warranty as detailed below:

  • Warranty - Parts: 5 Years
  • Warranty - Labor: 5 Years

For technical support, troubleshooting assistance, or warranty claims, please contact Dayton Audio customer service or visit the official Dayton Audio website for further resources.

Note: Warranty terms may vary based on region and retailer. Please retain your proof of purchase.

© 2023 Dayton Audio. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.