WeatherTech SP0213

WeatherTech Custom Scratch Protection Kit

Model: SP0213

For Hyundai Elantra GT - Door Handle Cups, Edges, Sills

Product Overview

The WeatherTech Custom Scratch Protection Kit is designed to shield your vehicle's vulnerable painted surfaces from everyday wear and tear. This practically invisible film provides durable protection against scratches, scuffs, and chips caused by rings, keys, cargo, boots, and other common sources of damage.

The kit is custom-fit for specific vehicle models, ensuring comprehensive coverage for areas such as door handle cups, door edges, and trunk sills. Made from clear, high-performance polyurethane, the film features self-healing technology that resists wear and discoloration, maintaining the aesthetic integrity of your vehicle's paint finish.

WeatherTech Scratch Protection Kit applied to a car door handle and sill

Image: WeatherTech Scratch Protection Kit applied to a vehicle's door handle and sill, showcasing its clear, protective nature.

Installation Guide

Proper installation is key to the longevity and effectiveness of your WeatherTech Scratch Protection Kit. Follow these steps carefully for optimal results.

Preparation:

  1. Clean the Surface: Thoroughly clean the vehicle's painted surface where the film will be applied. Ensure it is free of dirt, dust, wax, and any other contaminants. Use a mild soap and water solution, then rinse completely.
  2. Degrease (Optional): For best adhesion, a mild degreaser or rubbing alcohol (ensure it's safe for automotive paint) can be used after cleaning, followed by another rinse.
  3. Prepare Application Solution: Mix a few drops of baby shampoo (or a similar mild, pH-neutral soap) with water in a spray bottle. This "slip solution" will allow you to position the film.
  4. Prepare Tack Solution (if provided): Some kits may include a "tack solution" for final adhesion. Follow specific instructions for its use.

Application Steps:

  1. Spray Surface: Liberally spray the clean application area on your vehicle with the slip solution.
  2. Peel and Spray Film: Carefully peel the protective film from its backing. Immediately spray the adhesive side of the film with the slip solution.
  3. Position the Film: Place the wet, adhesive side of the film onto the wet surface of your vehicle. The slip solution will allow you to slide and adjust the film until it is perfectly aligned.
  4. Squeegee Out Water: Once positioned, use the provided squeegee (or a soft, rubber squeegee) to gently push out the water and air bubbles from under the film. Start from the center and work your way outwards, applying firm, even pressure.
  5. Wrap Edges (if applicable): For door edges, carefully wrap the film around the edge, ensuring a smooth, bubble-free application.
  6. Final Adhesion: If a tack solution is used, apply it as directed. Allow the film to dry and adhere completely. Avoid washing the vehicle or exposing the newly applied film to excessive moisture for at least 24-48 hours.
Hands applying clear protective film to a car door handle cup

Image: Step-by-step application of the clear protective film to a car's door handle cup.

Hands applying clear protective film to a car's trunk sill

Image: Application of the clear protective film to a vehicle's trunk sill area.

Instructional Video:

Video: Official WeatherTech guide demonstrating the application process for scratch protection film. (Duration: 1 minute 4 seconds)

Maintenance

The WeatherTech Scratch Protection Kit requires minimal maintenance. To ensure its longevity and clarity:

  • Regular Cleaning: Clean the film as you would the rest of your vehicle's exterior. Use mild automotive soap and water. Avoid harsh chemicals or abrasive cleaners.
  • Avoid Abrasives: Do not use abrasive brushes or cloths on the film, as this can scratch its surface.
  • Self-Healing Properties: Minor scratches on the film may self-heal over time, especially when exposed to warmth (e.g., sunlight).

Troubleshooting

ProblemPossible CauseSolution
Bubbles or WrinklesInsufficient slip solution; trapped air/water.Gently lift the film, re-spray with slip solution, and re-squeegee from the center outwards. Small bubbles may dissipate over a few days.
Film not adheringSurface not clean; not enough tack solution (if applicable); too much slip solution.Ensure surface is clean. If using tack solution, apply as directed. Allow more drying time.
Edges liftingImproper squeegee technique; not enough drying time.Press down firmly on lifting edges with a soft cloth or squeegee. Allow more time for adhesion. If persistent, re-apply with fresh film.

Specifications

  • Brand: WeatherTech
  • Model: SP0213
  • Material: High-performance polyurethane film
  • Color: Transparent
  • Coverage: Door Handle Cups, Door Edges, Trunk Sills
  • Compatibility: Select 2018-2020 Hyundai Elantra GT Models
  • Manufacturing: Made in USA
  • UPC: 787765685856
American flag with 'MADE IN USA' text

Image: Proudly Made in USA.

Warranty & Support

For specific warranty information and customer support, please refer to the official WeatherTech website or contact their customer service directly. WeatherTech stands behind the quality of its products.

Contact Information: