weelye JR1922RXS-D2 12V Remote Control and Receiver Kit Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your weelye JR1922RXS-D2 12V Remote Control and Receiver Kit. This kit is designed as a replacement part for specific children's electric ride-on cars. Please read this manual thoroughly before use to ensure proper function and safety.

2. Product Components

The weelye JR1922RXS-D2 kit includes the following main components:

• JR1922RXS-D2 12V Control Box (Receiver)
• JR1839FCC 2.4G Bluetooth Remote Control

Figure 2.1: Overview of the weelye JR1922RXS-D2 12V Remote Control and Receiver Kit, showing both the white remote control and the black receiver box.

Figure 2.2: The JR1922RXS-D2 12V Control Box, featuring its model number and electrical specifications on the label.

Figure 2.3: The JR1839FCC 2.4G Bluetooth Remote Control, a white handheld unit with black control buttons.

3. Safety Guidelines

Please observe the following safety warnings and guidelines:

• WARNING! Not for children under 3 years. Contains small parts which may present a choking hazard.
• Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity (+ and -).
• Exhausted batteries are to be removed from the toy promptly.
• The supply terminals are not to be short-circuited.
• Always supervise children when operating ride-on toys with remote control.

4. Installation and Setup

4.1 Compatibility Check

Before installation, ensure this control box is compatible with your electric ride-on car. Open your existing electric ride-on car and inspect its control box. If the appearance and model number (JR1922RXS-D2) of this control box match your original unit, it should be compatible.

4.2 Remote Control Battery Installation

The remote control requires two AAA (1.5V) batteries. Follow these steps to install them:

1. Locate the battery compartment on the back of the remote control.
2. Use a screwdriver to loosen the screw securing the battery compartment cover.
3. Remove the cover.
4. Insert two AAA (1.5V) batteries, ensuring correct polarity as indicated inside the compartment.
5. Replace the cover and tighten the screw.

Figure 4.1: Diagram illustrating how to loosen the screw and load two AAA (1.5V) batteries into the remote control.

4.3 Pairing Instructions (Matching Code)

To establish a connection between the remote control and the ride-on car's receiver, follow these steps:

1. Ensure the remote controller has two AAA batteries installed.
2. Turn off the power switch on the ride-on vehicle.
3. On the remote control, simultaneously hold down the "▲" (Forward) and "▼" (Back) keys for approximately 3 seconds. The first LED on the remote will begin to flicker, indicating it is in pairing mode.
4. While the remote's LED is flickering, turn on the power switch of the ride-on vehicle.
5. The red indicator lights on the remote control should stop flashing, indicating that the code matching process is successful.

Note: If this is the first time using the remote or if you are replacing it, you may need to perform this matching code procedure. If the remote control has been previously paired, it typically retains the memory of the match code and may not require re-pairing unless batteries are replaced or a new receiver is installed.

Figure 4.2: Excerpt from the JR1839FCC Remote Control Manual detailing the pairing process and button functions.

5. Operation

5.1 Remote Control Functions

The JR1839FCC remote control features the following buttons and their corresponding functions:

• "S" (Speed): Press to adjust the speed setting. One LED lit indicates low speed, two LEDs indicate medium speed, and three LEDs indicate high speed.
• "▲" (Forward): Moves the vehicle forward.
• "▼" (Back): Moves the vehicle backward.
• "◀" (Left): Turns the vehicle left.
• "▶" (Right): Turns the vehicle right.
• "P" (Brake/Stop): Press and hold this key to engage the brake. All LEDs on the remote will flicker when the brake is active.

The remote control also features a slow start function, eliminating the need for additional slow starter installations.

6. Specifications

7. Troubleshooting

• Remote not responding: Ensure batteries are correctly installed and not depleted. Re-perform the pairing procedure (Section 4.3).
• Intermittent control: Check for potential sources of interference. Ensure the remote and receiver are within effective range.
• Vehicle not powering on: Verify the vehicle's main power switch is on and its battery is charged. Check all connections to the control box.

8. Care and Maintenance

• Keep the remote control and receiver box dry and away from moisture.
• Clean the surfaces with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
• Store the kit in a cool, dry place when not in use.
• Remove batteries from the remote control if it will not be used for an extended period to prevent leakage.

9. Regulatory Information

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

10. Warranty and Support

Specific warranty information for this product is not provided in the available documentation. For warranty claims or technical support, please contact the retailer or manufacturer directly with your purchase details. Keep your proof of purchase for any support inquiries.