1. Introduction
The EVERBEAM P600 Anchor Light is designed to provide 360-degree visibility for marine vessels, enhancing safety during periods of darkness or restricted visibility. This light is suitable for power-driven and sailing vessels up to 65 feet (20 meters) in length. It features a durable, weatherproof construction and an adjustable fold-down design for versatile mounting options.
This manual provides essential information for the proper installation, operation, and maintenance of your EVERBEAM P600 Anchor Light.
2. Safety Information
Please read and understand all safety instructions before installing or operating the anchor light. Failure to follow these instructions may result in property damage, injury, or improper operation.
- Ensure the vessel's power supply is disconnected before beginning installation to prevent electrical shock.
- Verify that the light is installed in a location that provides unobstructed 360-degree visibility as required by maritime regulations.
- Use appropriate tools and personal protective equipment during installation.
- Confirm all electrical connections are secure and properly insulated to prevent short circuits and corrosion.
- This product is designed for marine use. Do not modify the light or use it for purposes other than its intended function.
3. Package Contents
Verify that all components are present before proceeding with installation:
- EVERBEAM P600 Anchor Light (6 Inch)
- Mounting Screws
- Red and Black Electrical Wires (pre-attached or included separately)
- Instruction Manual (this document)
Figure 3.1: Package Contents
4. Setup and Installation
Follow these steps for proper installation of the EVERBEAM P600 Anchor Light:
- Choose Mounting Location: Select a location on your vessel that ensures the anchor light provides an unobstructed 360-degree view. The light should be mounted as high as practical to maximize visibility.
- Prepare Mounting Surface: Ensure the mounting surface is clean, flat, and structurally sound.
- Mark Drill Holes: Position the light's base on the chosen surface and mark the locations for the mounting screws.
- Drill Pilot Holes: Drill pilot holes appropriate for the provided mounting screws. Exercise caution to avoid drilling into existing wiring or structural components.
- Secure the Base: Attach the light's base securely to the mounting surface using the provided screws.
- Wiring:
- Connect the red wire from the anchor light to the positive (+) terminal of your vessel's 12V or 24V DC power supply.
- Connect the black wire from the anchor light to the negative (-) terminal or a suitable ground point.
- Ensure all connections are watertight and protected from corrosion. It is recommended to use marine-grade connectors and heat shrink tubing.
- Adjust Light Angle: The P600 features a 180-degree adjustable fold-down design. Adjust the light to the desired vertical position and tighten the adjustment knob to secure it.
Figure 4.1: Anchor Light with Wiring
Figure 4.2: 180-Degree Adjustable Feature
5. Operating Instructions
Once installed and wired correctly, operating the EVERBEAM P600 Anchor Light is straightforward:
- Activation: Turn on the designated switch on your vessel's electrical panel that controls the anchor light circuit.
- Deactivation: Turn off the designated switch on your vessel's electrical panel.
- Visibility: The light provides 360-degree visibility for up to 3 nautical miles, ensuring your vessel is seen by others.
Figure 5.1: 360-Degree Visibility
6. Maintenance
Regular maintenance will ensure the longevity and optimal performance of your anchor light:
- Cleaning: Periodically clean the lens with fresh water and a soft cloth to remove salt spray, dirt, and debris. Avoid abrasive cleaners that could scratch the lens.
- Inspection: Regularly inspect the light for any signs of damage, corrosion, or loose connections. Check the mounting screws for tightness.
- Wiring: Ensure all wiring remains secure and free from fraying or damage.
- Storage: If the light is removed for storage, clean it thoroughly and store it in a dry, protected environment.
7. Troubleshooting
If you encounter issues with your EVERBEAM P600 Anchor Light, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on |
|
|
| Light flickers or is dim |
|
|
| Water inside the lens |
|
|
8. Specifications
| Model | P600 |
| Visibility | 360-degree, up to 3 nautical miles |
| LED Count | 36pc integrated LED array |
| Lifespan | Approximately 30,000 hours |
| Weatherproof Rating | IP66 (Marine Grade) |
| Material | ABS + 316 Stainless Steel |
| Adjustability | 180-degree fold-down design |
| Compatibility | USCG CFR 183.810 and ABYC A-16 standards |
| Vessel Length | Up to 65 feet (20 meters) |
| Item Weight | 8.8 ounces |
| Dimensions (6 Inch model) | 7.13 x 2.72 x 2.68 inches (Package) |
Figure 8.1: IP66 Weatherproof Rating
Figure 8.2: Compliance and Dimensions
9. Warranty and Support
EVERBEAM stands behind the quality of its products. The EVERBEAM P600 Anchor Light is backed by a 30-day money-back assurance. For technical support, warranty claims, or any questions regarding your product, please contact Everbeam customer service through the retailer where the product was purchased or visit the official Everbeam website.
Please retain your proof of purchase for warranty purposes.
