IQOS LIL SOLID 2.0 User Manual

1. Introduction

The IQOS LIL SOLID 2.0 is an innovative heat-not-burn device designed to provide a tobacco experience without combustion. It heats specially designed tobacco sticks to release a flavorful vapor, avoiding ash, smoke, and fire. This manual provides essential information for the safe and effective use of your device.

Image: The IQOS LIL SOLID 2.0 device (right), a cleaning tool (top left), and a USB-C charging cable (bottom left). The device is grey with a black top, the cleaning tool is orange and dark blue, and the cable is white.

2. Safety Information

Please read all safety warnings and instructions before using your IQOS LIL SOLID 2.0 device to prevent injury or damage.

• Keep out of reach of children and pets: This product contains small parts and electronic components that could pose a choking hazard or other risks.
• Use only with compatible tobacco sticks: Do not use with cigarettes or other tobacco products not designed for this device.
• Charging: Use only the provided charging cable and a certified power adapter. Do not charge near flammable materials or in direct sunlight.
• Avoid water and extreme temperatures: Do not expose the device to water, high humidity, or extreme temperatures.
• Do not disassemble: Attempting to disassemble or modify the device can cause injury and voids the warranty.
• Disposal: Dispose of the device and its components responsibly according to local regulations for electronic waste.

3. What's in the Box

Your IQOS LIL SOLID 2.0 Set includes:

• IQOS LIL SOLID 2.0 Device
• USB-C Charging Cable
• Cleaning Tool

4. Setup

4.1 Initial Charge

Before first use, fully charge your IQOS LIL SOLID 2.0 device. This typically takes approximately 2 hours.

1. Connect the USB-C charging cable to the charging port at the bottom of the device.
2. Connect the other end of the cable to a certified power adapter and plug it into a power outlet.
3. The LED indicator will blink during charging and turn solid when fully charged.

4.2 Turning On/Off

• To turn on, press and hold the button for 2 seconds. The device will vibrate, and the LED indicator will light up.
• To turn off, press and hold the button for 2 seconds. The device will vibrate, and the LED indicator will turn off.

5. Operating

5.1 Starting a Session

1. Ensure the device is charged and turned on.
2. Gently insert a compatible tobacco stick into the device's heating chamber with the tobacco end facing down. Do not twist the stick.
3. Press and hold the button for 2 seconds until the device vibrates. The LED indicator will blink, indicating pre-heating.
4. Once pre-heating is complete (approximately 25 seconds), the device will vibrate again, and the LED indicator will glow solid, indicating it's ready for use.

5.2 During the Session

A session lasts for approximately 5 minutes or 14 puffs, whichever comes first. The device will vibrate and the LED will blink to indicate the session is nearing its end.

5.3 Ending the Session

1. When the session ends, the device will vibrate, and the LED indicator will turn off.
2. To remove the used tobacco stick, gently twist it in one direction (either clockwise or counter-clockwise) 3 times, then pull it out.
3. Dispose of the used tobacco stick responsibly.

6. Maintenance

Regular cleaning ensures optimal performance and taste.

6.1 Regular Cleaning

Clean your device after every 20 tobacco sticks or as needed.

1. Ensure the device is turned off and cooled down.
2. Remove the cap from the device.
3. Separate the cleaning tool into its two parts: the scraper and the brush.
4. Use the scraper part to gently remove any large tobacco residue from the heating chamber.
5. Use the brush part to sweep away any remaining smaller particles from the heating chamber and inside the cap.
6. Reassemble the cleaning tool and store it.
7. Replace the cap on the device.

6.2 Deep Cleaning (Heat Cleaning)

The device has an automatic heat cleaning function.

• To activate, quickly press the button 5 times.
• The LED indicator will blink orange for approximately 90 seconds, indicating the heat cleaning process.
• Once complete, the LED will turn off.

7. Troubleshooting

7.1 Resetting the Device

If your device is not functioning correctly, a reset may resolve the issue.

• Press and hold the button for 8 seconds.
• The LED indicator will blink twice in red, then once in orange, and then turn off. This indicates the device has been reset.
• Release the button.

8. Specifications

• Model: LIL SOLID 2.0
• Manufacturer: IQOS
• Dimensions (Packaging): 17.5 x 14.4 x 3.9 cm
• Weight (Packaging): 420 Grams
• Battery: 1 Product-specific battery required (included)
• ASIN: B09Q761X2K

9. Warranty and Support

For detailed warranty information and customer support, please refer to the documentation included with your purchase or visit the official IQOS website. Warranty terms may vary by region.

For further assistance, you may contact IQOS customer service directly.