Instruction Manual for Ravelli Ecoteck Flame Arrester

1. Introduction

This manual provides essential information for the proper installation, maintenance, and safe use of the Ravelli Ecoteck Flame Arrester, part number 130-15-001N. This component is designed for specific Ravelli Ecoteck pellet stove models, including HR100, HRV120, HRV120 Style, HR evo14 Touch, and HRB120. The flame arrester is a critical safety component that prevents flames from propagating back into the fuel hopper, ensuring safe and efficient operation of your pellet stove.

2. Safety Information

Please read and understand all safety warnings before attempting any installation or maintenance. Failure to follow these instructions may result in property damage, serious injury, or death.

• Professional Installation Recommended: Installation and replacement of stove components should ideally be performed by a qualified technician.
• Disconnect Power: Always disconnect the pellet stove from the main power supply before performing any installation, maintenance, or inspection.
• Allow Cooling: Ensure the stove and all its components have completely cooled down before handling. Hot surfaces can cause severe burns.
• Wear Protective Gear: Use appropriate personal protective equipment (PPE), such as gloves and eye protection, to prevent injury from sharp edges or debris.
• Original Parts Only: Use only genuine or approved replacement parts to ensure proper fit and safe operation.
• Ventilation: Ensure adequate ventilation when working on the stove.

3. Setup and Installation

This flame arrester is a direct replacement part. The exact installation procedure may vary slightly depending on your specific Ravelli Ecoteck stove model. Refer to your stove's primary instruction manual for detailed disassembly and reassembly steps.

3.1. Pre-Installation Checks

1. Verify that the new flame arrester (Part No. 130-15-001N) matches the old component in size and design.
2. Inspect the new part for any manufacturing defects or shipping damage.
3. Gather necessary tools, which may include screwdrivers, wrenches, and a brush for cleaning.

3.2. Installation Steps (General)

1. Prepare the Stove: Ensure the stove is completely cool and disconnected from power.
2. Access the Component: Carefully open the stove's access panels or remove components as required to reach the existing flame arrester. Consult your stove's manual for specific access points.
3. Remove Old Part: Unfasten any screws or clips securing the old flame arrester and carefully remove it. Note its orientation for correct installation of the new part.
4. Clean Area: Thoroughly clean the area where the flame arrester sits, removing any ash, soot, or debris.
5. Install New Part: Position the new Ravelli Ecoteck Flame Arrester (130-15-001N) in the correct orientation. Secure it using the original screws or clips. Ensure it is firmly seated and does not wobble.
6. Reassemble: Reassemble any panels or components that were removed to access the flame arrester.
7. Final Check: Before reconnecting power, visually inspect the installation to ensure all connections are secure and no tools or debris are left inside the stove.

Image 1: The Ravelli Ecoteck Flame Arrester (Part No. 130-15-001N). This component is a flat, rectangular steel plate with a horizontal slot near one edge, designed to fit into specific Ravelli Ecoteck pellet stove models.

4. Operating Instructions

The flame arrester is a passive safety component and does not require direct user operation. Its function is integral to the safe operation of the pellet stove. Once correctly installed, ensure that the stove's primary functions (ignition, feeding, combustion) operate normally. If you notice any unusual behavior, such as smoke backflow or inconsistent flame, consult the stove's main manual or a qualified technician.

5. Maintenance

Regular maintenance of the flame arrester is crucial for the safe and efficient operation of your pellet stove. Ash and soot buildup can impede its function.

5.1. Cleaning Frequency

• Inspect the flame arrester during routine stove cleaning, typically every 1-2 weeks during active use.
• Perform a thorough cleaning at least once a month, or more frequently if using lower quality pellets that produce more ash.

5.2. Cleaning Procedure

1. Safety First: Ensure the stove is cool and disconnected from power.
2. Access: Open the necessary access panels to reach the flame arrester.
3. Remove: Carefully remove the flame arrester from its position.
4. Clean: Use a stiff brush or a vacuum cleaner with a fine particle filter to remove all ash, soot, and creosote buildup from the surface and slot of the flame arrester. Ensure the slot is completely clear.
5. Inspect: While cleaning, inspect the component for any signs of warping, cracks, or excessive wear. If damage is observed, the part should be replaced.
6. Reinstall: Reinstall the clean flame arrester, ensuring it is properly seated and secured.
7. Reassemble: Close all access panels.

6. Troubleshooting

Issues related to the flame arrester are typically due to improper installation or excessive buildup.

If troubleshooting steps do not resolve the issue, contact a qualified stove technician or the product seller for assistance.

7. Specifications

• Part Number: 130-15-001N
• Material: Steel
• Compatibility: Ravelli Ecoteck Pellet Stoves (HR100, HRV120, HRV120 Style, HR evo14 Touch, HRB120)
• Manufacturer: Ravelli
• ASIN: B09PZJJ6MR
• First Available on Amazon.it: February 5, 2022

8. Warranty

This product is a replacement part. For information regarding warranty coverage, please refer to the terms and conditions provided by the original seller or the manufacturer, Ravelli. Keep your proof of purchase for any warranty claims.

9. Support

For technical assistance, installation queries, or troubleshooting beyond the scope of this manual, please contact the seller from whom you purchased this product or an authorized Ravelli service center. Always provide the part number (130-15-001N) and your stove model when seeking support.