Sena 50C Motorcycle Communication & 4K Camera System Instruction Manual

Introduction

The Sena 50C is an advanced communication and camera system designed for motorcycle riders. It integrates Sena's Mesh and Bluetooth communication technologies with a high-resolution 4K camera, offering a comprehensive audio and video experience. Featuring SOUND BY Harman Kardon speakers and microphone, the 50C delivers superior audio clarity for communication and media playback.

Setup

This section guides you through the initial setup of your Sena 50C device, including powering it on and pairing it with your mobile phone.

Initial Power On and Phone Pairing

To power on your 50C for the first time, press the Jog Dial and hold the Phone Button simultaneously for approximately 1 second. The device will automatically enter phone pairing mode, indicated by a tiny light blinking red and blue. If you do not wish to pair your phone immediately, tap the Jog Dial to exit this mode.

To enter phone pairing mode later, press and hold the Phone Button for 5 seconds until the light blinks red and blue.

Setup Overview Video

Official Sena '50C Tech Talk' video (Creator Type: Vendor). This segment covers unboxing and initial power-on/pairing (0:04 - 0:08, 0:58 - 1:10, 1:18 - 1:50).

Operating Instructions

Learn how to control various functions of your Sena 50C during your ride.

Volume and Music Control

To adjust the volume, scroll the Jog Dial backward to increase volume and forward to decrease volume. To start music playback from your phone's playlist, press and hold the Jog Dial for 1 second. The device will pick up where it last left off. To scroll through your music, press and hold the Jog Dial while turning it backward or forward.

Intercom Communication

The 50C offers two primary intercom options: Mesh Intercom and Bluetooth Intercom.

Mesh Intercom

To activate Mesh Intercom, open the antenna on the device and tap the Mesh Intercom button once. Your device will automatically connect to the Mesh network and seek out other devices on the same channel. A flashing green light indicates connection to the Mesh network. If you experience interference, you can change channels by tapping the Mesh button twice to enter channel selection mode, then use the Jog Dial to select one of the nine available channels.

Bluetooth Intercom

Bluetooth Intercom allows connection with up to four riders. To enter Bluetooth pairing mode, press and hold the Jog Dial until you hear "Intercom Pairing." The light will blink red. The other rider must also perform the same action. Once both devices are in pairing mode, one person needs to tap the Jog Dial to initiate the connection.

Mesh Reach-Out Feature

The Mesh button also enables the Mesh Reach-Out feature. This allows you to send an audio invitation to nearby Sena users with a Mesh-ready device to connect to your Mesh network. To send an invitation, tap the Mesh button three times. Recipients will hear a message in their helmet. If they wish to join, they simply tap their Mesh button once. Both parties must have this setting enabled via the Sena Motorcycles App.

Camera Operation

The 50C features an integrated 4K camera for recording your rides.

Turning Camera On/Off

The camera button is located on the underside of the 50C. Tap it once to turn the camera on. To turn the camera off, tap the camera button and the Phone button simultaneously.

Recording Video and Taking Photos

To start recording video, press and hold the camera button for 1 second. To stop recording, press and hold the camera button for 1 second again. To take a still picture, tap the camera button once.

Camera Operation Video

Official Sena '50C Tech Talk' video (Creator Type: Vendor). This segment demonstrates camera button commands and operations (4:35 - 5:29).

Maintenance

Proper maintenance ensures the longevity and optimal performance of your Sena 50C.

MicroSD Card Management

To record video, a MicroSD card (not included) is required. Open the cover on the bottom of the device to find the MicroSD slot. Insert your card and ensure the cover is closed tightly.

To format your MicroSD card, press and hold the camera button for 5 seconds until you hear "Format SD Card." Then, press the Phone button once. You will hear "SD Card Formatted" upon completion.

Charging

The charging port is located next to the MicroSD card slot and works with USB-C cables. You can use the included Wi-Fi USB-C cable or any standard USB-C cable. The device can be used while plugged in, allowing for extended recording if connected to a motorcycle's USB charge port or a portable battery pack.

Maintenance Overview Video

Official Sena '50C Tech Talk' video (Creator Type: Vendor). This segment covers MicroSD card management and charging (5:00 - 5:21, 6:05 - 6:15).

Troubleshooting

If you encounter issues with your Sena 50C, consider the following steps:

• Firmware Updates: Some users have reported issues that were resolved by updating the firmware. It is recommended to use the "Sena Device Manager" on a PC for updates, as the Wi-Fi adapter and phone app may not always provide the latest version.
• Voice Prompts: If voice prompts stop working, a firmware update or factory reset might be necessary.
• Connectivity: Ensure proper pairing procedures are followed for both phone and intercom connections. For Mesh, try changing channels if interference occurs.
• Camera App Issues: If the camera app is not functioning correctly, check for app updates or consult the Sena support resources.

Specifications

Warranty and Support

For detailed warranty information and technical support, please refer to the official Sena website or contact their customer service directly. Keep your purchase receipt for warranty claims.