Introduction
This manual provides detailed instructions for the safe and effective operation of your Godox Ving V860III TTL Li-Ion Flash for Sony cameras. Please read this manual thoroughly before use to ensure proper function and to prevent damage to the product or injury to yourself.
What's Included
Carefully unpack the box and ensure all items listed below are present and in good condition. If any items are missing or damaged, contact your retailer immediately.
Image: All components included in the Godox V860III flash kit, neatly arranged.
- V860III Flash Unit
- VB26 Li-Ion Battery
- Battery Charger
- USB Cable
- Mini Stand
- Protective Case
- Instruction Manual (this document)
Product Overview
The Godox V860III flash unit incorporates several features designed to enhance your photography experience.
Modeling Light for Pre-visualization
Image: The modeling light on the V860III flash head, used for previewing light effects.
A modeling light is integrated into the flash head to assist in previewing the light effect before shooting. This feature includes 10-level dimmable brightness, allowing for precise adjustment and better visualization of lighting techniques.
Quick Switch for Mode Control
Image: The quick switch button on the V860III for fast toggling between Manual (M) and TTL modes.
The V860III features a quick switch button, enabling rapid transitions between Manual (M) and TTL (Through-The-Lens) flash modes for efficient workflow.
Zoomable Flash Head
Image: The LCD display of the V860III showing zoom settings, with a hand adjusting the control dial.
The flash head offers a zoom range from 20mm to 200mm, adjustable automatically or manually. This allows for precise control over the light spread, whether for broad coverage or focused illumination.
Setup
1. Battery Installation
- Ensure the flash unit is powered off.
- Locate the battery compartment on the side of the flash unit.
- Slide the battery compartment cover open.
- Insert the VB26 Li-Ion battery, aligning the contacts correctly.
- Close the battery compartment cover until it clicks securely into place.
2. Charging the Battery
- Connect the battery charger to a power outlet.
- Insert the VB26 battery into the charger.
- The charging indicator on the charger will show the charging status. Charge until the indicator shows a full charge.
- Disconnect the charger once charging is complete.
3. Mounting the Flash on a Camera
- Ensure both the camera and flash unit are powered off.
- Slide the flash's mounting foot into your camera's hot shoe.
- Rotate the locking ring or lever on the flash unit clockwise until it is securely fastened to the hot shoe. Do not overtighten.
Operating Instructions
1. Power On/Off
- To power on, slide the power switch to the 'ON' position.
- To power off, slide the power switch to the 'OFF' position.
2. TTL Automatic Flash Mode
- Press the 'TTL/M' quick switch button to select TTL mode. The LCD display will show 'TTL'.
- In TTL mode, the flash output is automatically adjusted by the camera to achieve correct exposure.
- You can adjust Flash Exposure Compensation (FEC) using the control dial to fine-tune exposure.
3. Manual Flash Mode
- Press the 'TTL/M' quick switch button to select Manual mode. The LCD display will show 'M'.
- In Manual mode, you set the flash output power manually. Use the control dial to adjust the power from 1/1 (full power) to 1/256 (minimum power).
4. Wireless Flash Operation
The V860III supports both optical and 2.4G wireless transmission for off-camera flash control.
- 2.4G Wireless Mode: Press the 'SYNC' button to enter wireless mode. Use the control dial and function buttons to set the flash as a Master or Slave unit, select channels, and groups. Refer to the detailed wireless section in the full manual for advanced settings.
- Optical Pulse Mode: This mode uses light pulses for communication. Ensure a clear line of sight between the master and slave units.
5. Adjusting Flash Settings
- Zoom: Press the 'ZOOM' button and use the control dial to manually adjust the flash head's zoom position.
- Modeling Light: Press the dedicated modeling light button to turn it on/off and use the control dial to adjust its brightness.
- High-Speed Sync (HSS): Activate HSS through the camera's flash menu or the flash unit's settings if supported by your camera model.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the flash unit. For stubborn dirt, a slightly damp cloth can be used, followed by a dry cloth. Do not use strong detergents or solvents.
- Storage: When not in use for extended periods, remove the battery and store the flash unit in a cool, dry place, away from direct sunlight and extreme temperatures.
- Battery Care: Recharge the battery regularly, even if not in use, to maintain its lifespan. Avoid fully discharging the battery.
Troubleshooting
If you encounter issues with your flash unit, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Flash does not fire. | Low battery; incorrect camera/flash settings; flash not securely mounted. | Charge or replace battery; check flash mode (TTL/M) and camera settings; ensure flash is firmly attached to hot shoe. |
| Flash output is too bright/dark. | Incorrect flash exposure compensation (FEC) or manual power setting. | Adjust FEC in TTL mode or manual power level in M mode. Check camera ISO and aperture settings. |
| Wireless trigger not working. | Incorrect channel/group settings; distance too far; interference. | Verify master and slave units are on the same channel and group; reduce distance; check for obstructions. |
| Flash head does not zoom. | Flash in manual zoom mode; mechanical obstruction. | Ensure flash is in auto zoom mode or manually adjust zoom; check for any physical obstructions. |
If the problem persists after trying these solutions, please contact customer support.
Specifications
- Brand: GODOX
- Model Number: V860IIIS
- Compatible Mountings: Sony Alpha
- Wireless Communication Technology: Optical Pulse, Radio Frequency (2.4G)
- Power Source: Li-Ion Battery (VB26)
- Zoom Range: 20-200mm (Auto/Manual)
- Modeling Light: 10-level dimmable
- ASIN: B09PRPXNLD
Warranty and Support
For warranty information and technical support, please refer to the warranty card included with your product or visit the official Godox website. Keep your purchase receipt as proof of purchase for warranty claims.
