Ultima Cosa Presto Freddo ICM-1227
Ultima Cosa Presto Freddo High Capacity Ice Maker
User Manual
Model: Presto Freddo (ICM-1227)
Brand: Ultima Cosa
1. Introduction
Thank you for choosing the Ultima Cosa Presto Freddo High Capacity Ice Maker. This appliance is designed to provide fresh, bullet-shaped ice cubes quickly and efficiently, perfect for various beverages and occasions. With its compact design and smart features, it offers convenience and reliability for your home, office, or outdoor gatherings. This manual provides essential information for safe operation, maintenance, and troubleshooting to ensure optimal performance of your ice maker.

2. Important Safety Instructions
To reduce the risk of fire, explosion, electric shock, or injury when using your ice maker, follow these basic safety precautions:
- Read all instructions before use.
- Do not touch the evaporator or ice blades when the unit is operating.
- Do not immerse the appliance, power cord, or plug in water or other liquids.
- Ensure the appliance is properly grounded.
- Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
- Keep the power cord away from heated surfaces.
- Do not place the appliance on or near a hot gas or electric burner, or in a heated oven.
- Use only potable water for ice production.
- Do not use the appliance for other than its intended use.
- Unplug the ice maker before cleaning or performing any maintenance.
- Supervise children when the appliance is in use.
3. Package Contents
Upon unpacking your Ultima Cosa Presto Freddo Ice Maker, please ensure all items listed below are present and in good condition:
- Ultima Cosa Presto Freddo Ice Maker Main Unit
- Ice Basket
- Ice Scoop
- User Manual
4. Product Overview
Familiarize yourself with the components and control panel of your ice maker for optimal use.

Key Components:
- Control Panel: Features indicator lights for 'Ice Full', 'Add Water', and 'Self-Cleaning', along with power and ice size selection buttons.
- Water Reservoir: Located at the bottom, holds water for ice production.
- Ice Basket: Removable basket to collect produced ice cubes.
- Transparent Viewing Window: Allows you to monitor the ice making process without opening the lid.
- Air Vents: Located on the sides and back, essential for proper ventilation and cooling.
5. Setup
Unpacking and Placement:
- Remove all packaging materials and check for any damage.
- Place the ice maker on a flat, stable surface, away from direct sunlight and heat sources. Ensure there is at least 15 cm (6 inches) of space around the unit for proper ventilation.
- Allow the unit to stand upright for at least 2 hours before plugging it in, especially if it was transported horizontally. This allows the refrigerant to settle.
Initial Cleaning:
Before first use, clean the interior of the ice maker:
- Open the lid and remove the ice basket.
- Clean the interior liner, ice basket, and ice scoop with a soft cloth dampened with warm water and a mild detergent.
- Rinse thoroughly and wipe dry.
- Drain any remaining water through the drain plug at the bottom of the unit.
6. Operating Instructions
Adding Water:
- Ensure the drain plug is securely closed.
- Open the lid and remove the ice basket.
- Fill the water reservoir with potable water up to the MAX fill line. Do not overfill.
- Replace the ice basket and close the lid.
Making Ice:
- Plug the ice maker into a grounded electrical outlet.
- Press the 'POWER' button to turn on the unit. The 'POWER' indicator will illuminate.
- Select your desired ice cube size (Small or Large) by pressing the 'SELECT' button. The corresponding indicator light will illuminate.
- The ice maker will begin the ice production cycle. The first batch of ice typically takes about 7 minutes.

Smart Functions:
- Ice Full Indicator: When the ice basket is full, the 'ICE FULL' indicator light will turn on, and the ice making process will pause. Remove ice to resume operation.
- Add Water Indicator: If the water level in the reservoir is too low, the 'ADD WATER' indicator light will turn on. Add water to the reservoir to continue ice production.

7. Maintenance and Cleaning
Regular cleaning and maintenance will extend the life of your ice maker and ensure hygienic ice production.
Self-Cleaning Function:
The ice maker features a convenient self-cleaning mode:
- Ensure the unit is empty of ice and water.
- Fill the water reservoir with clean water up to the MAX line.
- Press and hold the 'CLEAN' button (or indicated self-clean button) for a few seconds to activate the self-cleaning cycle. The indicator light will illuminate.
- The cycle will run for approximately 20-30 minutes, circulating water to clean the internal components.
- Once the cycle is complete, drain the water from the unit by opening the drain plug at the bottom.
- Rinse the reservoir with fresh water and drain again.

General Cleaning:
- Exterior: Wipe the exterior with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Interior: Periodically clean the water reservoir and ice basket with a mild detergent and warm water. Rinse thoroughly.
- Draining: Always drain unused water from the reservoir if the unit will not be used for an extended period.
8. Troubleshooting
If you encounter issues with your ice maker, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Ice maker not working | No power; 'ADD WATER' indicator on | Check power connection; Add water to reservoir |
| Ice cubes are small or clumpy | Water temperature too high; Ambient temperature too high | Use colder water; Place unit in a cooler environment |
| Ice full indicator is on, but basket is not full | Ice cubes are blocking the sensor | Rearrange ice cubes or remove some |
| Water leaks from unit | Drain plug not closed; Unit not level | Ensure drain plug is securely closed; Place unit on a level surface |
| Unusual noise during operation | Normal operation sounds; Unit not level | Some sounds are normal; Ensure unit is on a level surface |
If the problem persists after attempting these solutions, please contact customer support.
9. Specifications
Technical specifications for the Ultima Cosa Presto Freddo High Capacity Ice Maker:
| Feature | Specification |
|---|---|
| Product Dimensions | 30.8 x 22.4 x 28.3 cm |
| Weight | 8.7 kg |
| Model Name | Presto Freddo |
| Manufacturer Reference | ICM-1227 |
| Capacity (Water Tank) | 1.5 liters |
| Voltage | 120 Volts (AC) |
| Refrigerant | R600a |
| Daily Ice Output | Up to 12 kg (26 lbs) / 24 hours |
| First Ice Out | Less than 7 minutes |
| UPC | 700445319742 |

10. Warranty and Support
The Ultima Cosa Presto Freddo High Capacity Ice Maker comes with a standard manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions, including coverage period and limitations.
For technical support, troubleshooting assistance, or warranty claims, please contact Ultima Cosa customer service. Contact information can typically be found on the product packaging, the official Ultima Cosa website, or the warranty card.
When contacting support, please have your model number (ICM-1227) and proof of purchase readily available.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.