1. Introduction
This manual provides comprehensive instructions for the installation and operation of your Start-X F3-Edge Remote Start Kit. This system allows you to remotely start your Ford Edge using your existing factory key fob, enhancing comfort and convenience. Please read this manual thoroughly before beginning installation or operation.
Image 1.1: Start-X Remote Start Kit for Ford Edge (2015-2019) overview.
2. Compatibility
- Vehicle Models: Ford Edge (Model Years: 2015, 2016, 2017, 2018, 2019).
- Ignition Type: Compatible with both Key Start and Push-to-Start ignition systems.
- Transmission Type: Designed for automatic transmission models only. Not compatible with manual transmission vehicles.
- Fuel Type: Compatible with gas models only. Not compatible with diesel models.
- Factory Remote: Requires an existing factory remote for operation. The kit does not include a remote.
Image 2.1: The system requires your vehicle's factory remote.
Image 2.2: Compatible with gas models only.
Image 2.3: For automatic transmission vehicles only.
3. Safety Information
Please observe the following safety precautions to ensure safe operation and prevent damage to your vehicle or the remote start system:
- Ensure the vehicle is in a well-ventilated area before remote starting, especially if parked indoors.
- Never remote start a vehicle if a child or pet is inside.
- Confirm the vehicle is in Park (P) before attempting to remote start.
- Do not attempt to install or operate the system if you are unsure about any step. Consult a qualified technician.
- Keep hands and clothing clear of moving engine parts when the vehicle is running.
4. Package Contents
The Start-X Remote Start Kit typically includes the following components:
- Start-X Remote Start Module (F3-Edge)
- Vehicle-specific T-Harness
- Zip ties for securing wiring
- Instruction Manual (this document)
Image 4.1: Main remote start module and T-harness.
5. Setup and Installation
The Start-X Remote Start Kit is designed for a plug-and-play installation, requiring no wire cutting or splicing. Installation typically takes approximately 5-15 minutes.
5.1 Pre-Installation Checklist
- Ensure your vehicle is turned off and the key is removed from the ignition (if applicable).
- Gather necessary tools: typically none are required beyond your hands, but a trim removal tool may be helpful for accessing panels.
- Verify all package contents are present.
5.2 Installation Steps
- Locate Vehicle Connectors: Identify the vehicle's wiring harness connector located to the right of the steering column, typically further up under the dash. Refer to your vehicle's service manual if needed.
- Connect T-Harness: Disconnect the factory connector from its port. Connect the Start-X T-Harness in-line with the factory wiring. One end of the T-Harness connects to the vehicle's port, and the other end connects to the factory connector you just removed.
- Connect Module: Plug the Start-X remote start module into the designated connector on the T-Harness.
- Program the Module: Follow the specific programming instructions provided with your kit. This usually involves a sequence of key turns or button presses to synchronize the module with your vehicle's system. The module's LED indicators will guide you through this process.
- Secure Wiring: Once the module is programmed and connections are confirmed, use the provided zip ties to secure the module and excess wiring, ensuring they do not interfere with pedals or moving parts.
Image 5.1: Example of connecting the plug-and-play T-Harness.
Image 5.2: Visual representation of the three main installation steps.
6. Operating Instructions
The Start-X Remote Start Kit utilizes your vehicle's existing factory remote for operation.
6.1 Remote Starting Your Vehicle
To remote start your Ford Edge:
- Ensure your vehicle is locked.
- Press the LOCK button on your factory remote.
- Press the UNLOCK button on your factory remote.
- Press the LOCK button on your factory remote again.
The vehicle should start within a few seconds. The parking lights may flash to indicate successful remote start. The engine will run for a preset duration (typically 15 minutes) or until you enter the vehicle and press the brake pedal, or repeat the lock-unlock-lock sequence.
Image 6.1: Using the factory remote to initiate remote start.
6.2 Entering the Vehicle After Remote Start
To enter and drive your vehicle after a remote start:
- Unlock the vehicle using your factory remote.
- Open the door and enter the vehicle.
- Insert your key into the ignition and turn it to the ON/RUN position (for key start models) or press the brake pedal (for push-to-start models).
- The remote start system will disengage, and you can drive normally.
7. Maintenance
The Start-X Remote Start Kit is designed to be maintenance-free. No periodic servicing is required for the module itself. Ensure all connections remain secure and free from moisture or physical damage.
- Periodically check the wiring and module for any signs of wear or damage.
- Keep your factory remote in good working condition, including replacing its battery as needed.
8. Troubleshooting
If you encounter issues with your Start-X Remote Start Kit, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Vehicle does not remote start. |
|
|
| Remote start engages, but vehicle shuts off immediately. |
|
|
| "To drive press brake and start button" message on IPC. | Known issue with some 2015 Ford Edge models (TSB SSM 45145). | This may require a software update to the Instrument Panel Cluster (IPC) by a Ford dealer. Contact Start-X support for further guidance. |
If the problem persists after attempting these solutions, please contact Start-X technical support.
9. Specifications
- Model Number: F3-Edge
- Brand: Start-X
- Compatibility: Ford Edge (2015-2019), Gas models, Automatic Transmission, Key Start & Push-to-Start.
- Installation Type: Plug-and-Play (no wire cutting/splicing)
- Operation: Uses factory remote (LOCK-UNLOCK-LOCK sequence)
- Module Dimensions: Approximately 2 x 8 x 4 inches (5.08 x 20.32 x 10.16 cm)
- Item Weight: Approximately 9.9 ounces (280 grams)
- Designed & Manufactured: North America
10. Warranty and Support
Start-X products are designed and manufactured in North America. For specific warranty details, please refer to the warranty card included with your product or visit the official Start-X website. Technical support agents are located in the USA and provide support in English.
For technical assistance, troubleshooting, or warranty claims, please contact Start-X customer support through their official channels. You may also find additional resources and installation videos on their website or YouTube channel.
- Online Resources: Start-X Official Website
- Support Contact: Refer to the product packaging or official website for current contact information.
