glacio 4 Cavity - Sphere

Download PDF
Contents

glacio Clear Ice Maker Set Instruction Manual

Model: 4 Cavity - Sphere (ASIN: B09PCBBTTS)

Brand: glacio

Introduction

This manual provides instructions for the glacio Clear Ice Maker Set, designed to produce crystal clear ice spheres for beverages. Utilizing directional freezing technology, this set minimizes impurities, resulting in slow-melting ice that enhances the taste and aroma of your drinks without dilution. The set includes components for creating four 2.4-inch ice spheres.

Product Components

  • Outer insulated container (black)
  • Silicone ice sphere molds (4 cavities)
  • Top lid/tray for molds
glacio Clear Ice Maker Set components including the black insulated container and silicone molds.

Image: The glacio Clear Ice Maker Set, showing the insulated container, silicone molds, and a finished ice sphere in a glass.

Setup and First Use

  1. Clean Components: Before first use, wash all parts of the ice maker set with warm, soapy water. The silicone molds are dishwasher safe. Rinse thoroughly and allow to air dry.
  2. Assemble Molds: Ensure the two halves of each silicone sphere mold are properly aligned and sealed.
  3. Fill Container: Fill the black insulated container with filtered water up to the indicated fill line (a vertical marker on one of the inner sides). Using filtered water is recommended for optimal clarity.
  4. Insert Molds: Carefully place the assembled silicone molds into the water-filled container. Gently push them down until they are fully submerged and seated. Excess water may overflow into the grooves on top, which is normal.
  5. Freeze: Place the entire assembled unit into your freezer. Ensure there is adequate space for the unit (Product Dimensions: 7.3"L x 8.82"W x 7.83"H).
Dimensions of the glacio ice maker set.

Image: Diagram showing the dimensions of the glacio ice maker set: 7.75" width, 7.5" depth, and 6.75" height.

Operating Instructions

  1. Freezing Time: Allow the ice maker to freeze for approximately 24 to 36 hours. The exact time may vary depending on your freezer's temperature.
  2. Ice Removal: Once frozen, remove the unit from the freezer. Gently pull the silicone molds upwards, alternating sides if necessary, to separate them from the frozen block at the bottom of the container. The ice spheres will be contained within the silicone molds.
  3. Serve: Carefully remove the clear ice spheres from the silicone molds. For best results, allow the ice spheres to sit for a few minutes at room temperature before placing them into your beverage. This allows the surface to temper slightly, reducing the risk of cracking and enhancing clarity.
A clear ice ball being placed into a glass of whiskey using tongs.

Image: A perfectly clear ice sphere being carefully placed into a glass of whiskey using ice tongs, highlighting its elegant appearance.

A clear ice ball in a glass of whiskey on a bar counter.

Image: A clear ice sphere resting in a glass filled with whiskey, showcasing its minimal dilution and aesthetic appeal.

Maintenance and Cleaning

The glacio Clear Ice Maker Set is designed for easy maintenance.

  • After each use, rinse all components with warm water to remove any ice residue or film.
  • The silicone molds are dishwasher safe for convenient cleaning.
  • The insulated container can be hand-washed with mild soap and water.
  • Ensure all parts are completely dry before storing to prevent ice buildup or odors.

Troubleshooting

ProblemPossible Cause / Solution
Ice spheres are cloudy or not perfectly clear.This can be due to impurities in the water. Use filtered or distilled water for best results. Ensure the unit is placed in a stable, level position in the freezer.
Difficulty removing ice spheres from molds.The ice may be too cold or the mold is stuck to the bottom ice block. Allow the unit to sit at room temperature for a few minutes (5-10 minutes) to slightly temper the ice before attempting removal. Gently pull the silicone molds from alternating sides.
Ice spheres are not fully formed or have flat spots.Ensure the container is filled to the correct water level and the silicone molds are fully submerged and seated before freezing. Insufficient water or improper mold placement can lead to incomplete spheres.
Unit takes too long to freeze.Freezing time can vary based on freezer temperature. Ensure your freezer is set to an appropriate temperature (around 0°F / -18°C). The recommended freezing time is 24-36 hours.

Specifications

FeatureDetail
Brandglacio
Model4 Cavity - Sphere (ASIN: B09PCBBTTS)
MaterialSilicone (BPA Free)
ColorBlack
Product Dimensions7.3"L x 8.82"W x 7.83"H
Item Weight2.6 Pounds
Dishwasher SafeYes
Ice Sphere Size2.4-inch diameter (approx.)

Warranty and Support

For warranty information or product support, please refer to the contact details provided with your purchase or visit the official glacio website. Keep your proof of purchase for any warranty claims.

© 2024 glacio. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.