SmallRig Full Camera Cage 3667B Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the SmallRig Full Camera Cage 3667B. This camera cage is designed to enhance the functionality and protection of compatible Sony Alpha series cameras.

Figure 1: SmallRig Full Camera Cage 3667B installed on a Sony Alpha camera. This image shows the cage providing a protective frame around the camera body, with various mounting points visible.

2. Compatibility

The SmallRig Full Camera Cage 3667B is specifically designed for the following Sony Alpha camera models:

• Sony Alpha 7R V
• Sony Alpha 7 IV
• Sony Alpha 7S III
• Sony Alpha 1
• Sony Alpha 7R IV

Important Note: The Cable Clamp for HDMI 3000 is not compatible with Alpha 1 and Alpha 7R IV when used with this cage, as it may obstruct the synchro terminal interface on the Alpha 7R V.

Figure 2: Compatibility diagram illustrating the modular design of the cage's locking slider. The slider can be adjusted for Alpha 7 IV / Alpha 7R V or Alpha 7S III / Alpha 1 / Alpha 7R IV models. This ensures a secure fit across various compatible cameras.

3. Installation Guide

Follow these steps to securely install the SmallRig Full Camera Cage 3667B onto your compatible Sony Alpha camera.

3.1. Preparing the Camera

• If present, remove the shoulder strap hook from the left side of your camera. This is necessary to properly use the cage's locking slider.

3.2. Attaching the Cage (Three-Point Locking System)

1. Align the camera with the cage, ensuring the bottom 1/4"-20 screw hole on the camera matches the corresponding hole on the cage.
2. Insert and tighten the 1/4"-20 screw located at the bottom of the cage into the camera's tripod socket.
3. Locate the M2.5 screw on the left side of the cage. This screw, along with the 1/4"-20 screw and a positioning pin, forms a three-point locking system for enhanced stability.
4. Adjust the direction of the left locking slider to match your specific camera model:
   • Use the [A7 IV] side for Sony Alpha 7 IV and Alpha 7R V.
   • Use the [A7S III/A1] side for Sony Alpha 7S III, Alpha 1, and Alpha 7R IV.
5. After fixing the bottom 1/4"-20 screw, retrieve the anti-deflection pin from its temporary storage hole and insert it into the corresponding position on the cage to further secure the camera.

Figure 3: Detailed view of the three-point locking system. This image highlights the 1/4"-20 screw, M2.5 screw, and the added positioning pin that work together to secure the camera within the cage, preventing twisting.

4. Features and Usage

The SmallRig Full Camera Cage 3667B offers a range of features designed to enhance your camera's versatility and protection.

4.1. Multiple Mounting Points

The cage provides numerous attachment points for various accessories:

• 1/4"-20 Threaded Holes: Located throughout the cage for attaching accessories like magic arms, monitor mounts, and more.
• 3/8"-16 ARRI Locating Holes: For accessories requiring anti-twist mounting, such as top handles (e.g., SmallRig Handle 3765) or monitor mounts (e.g., SmallRig Monitor Mount 2903B).
• Cold Shoe Mounts: Two built-in cold shoe interfaces (one on the upper right corner) for microphones (e.g., SmallRig Microphone 3468) or LED video lights (e.g., SmallRig LED Video Light 3286).
• QD Hole: A Quick Detach (QD) hole at the bottom is compatible with QD quick release shoulder straps.
• Strap Slots: Reserved holes on both sides and the bottom of the cage allow attachment of wrist straps (e.g., SmallRig Wrist Strap PAC2456) and shoulder straps (e.g., SmallRig Shoulder Strap PSC2428).

Figure 4: Illustration of the multiple mounting points available on the cage, including 1/4"-20 threaded holes, 3/8"-16 ARRI locating holes, cold shoe mounts, and strap slots, providing extensive accessory attachment options.

4.2. All-Round Protection

The cage is designed to protect your camera while maintaining full accessibility:

• Rubber Gasket: A built-in all-round rubber gasket prevents scratches and protects the camera body from direct contact with the metal cage.
• Unobstructed Access: With the cage installed, all camera interfaces, dials, buttons, and the battery compartment remain fully accessible.
• Battery Compartment Wrench: The battery compartment features an opening and closing wrench design that conforms to the camera's fuselage curve, improving grip and facilitating battery changes.

Figure 5: Visual representation of the cage's protective features, including the rubber gaskets and the design that ensures full access to camera controls and the battery compartment.

4.3. Integrated Arca-Swiss Quick Release Plate

The bottom of the cage features an integrated Arca-Swiss quick release plate for rapid mounting and dismounting on compatible tripods and stabilizers.

• Additional 1/4"-20 Holes: The quick release plate includes additional 1/4"-20 holes with 18mm spacing, compatible with DJI RS 2 / RSC 2 / RS 3 / RS 3 Pro stabilizers and the SmallRig Quick Release Plate for Arca 3154.

Figure 6: Detailed view of the cage's bottom, highlighting the integrated Arca-Swiss quick release plate, additional 1/4"-20 threaded holes, and the hinge arm for battery access. A flat screwdriver is also shown, often magnetically stored within the cage.

5. Maintenance

To ensure the longevity and optimal performance of your SmallRig Full Camera Cage 3667B, follow these maintenance guidelines:

• Cleaning: Wipe the cage with a soft, dry cloth to remove dust and debris. For stubborn dirt, use a slightly damp cloth and dry thoroughly. Avoid harsh chemicals or abrasive materials.
• Inspection: Periodically check all screws and mounting points for tightness. Ensure the rubber gaskets are intact and free from damage.
• Storage: Store the cage in a dry, clean environment when not in use.

6. Troubleshooting

This section addresses common issues and considerations when using the SmallRig Full Camera Cage 3667B.

• Cage Not Fitting Correctly: Ensure the left locking slider is set to the correct position for your specific camera model ([A7 IV] for Alpha 7 IV/7R V; [A7S III/A1] for Alpha 7S III/Alpha 1/7R IV). Verify that the shoulder strap hook on the camera's left side has been removed.
• Accessory Obstruction: Be aware that the SmallRig Cable Clamp for HDMI 3000 is not compatible with Alpha 1 and Alpha 7R IV when the cage is installed, as it may block the synchro terminal interface on the Alpha 7R V.
• Loose Camera: Confirm that both the 1/4"-20 screw and the M2.5 screw are fully tightened, and the anti-deflection pin is correctly seated.

7. Specifications

Key specifications for the SmallRig Full Camera Cage 3667B:

Figure 7: Visual summary of the package contents (Cage x 1) and a table detailing the product's material, compatibility, dimensions, and weight.

8. Warranty and Support

For information regarding product warranty, returns, or technical support, please refer to the official SmallRig website or contact your retailer. Protection plans may be available for purchase separately to extend coverage beyond the standard manufacturer's warranty.