1. Introduction
Thank you for choosing the Artika Swirl Integrated LED Floor Lamp. This modern and functional lighting solution is designed to enhance your living space with its unique aesthetic and brilliant illumination. This manual provides essential information for safe installation, operation, and maintenance of your new floor lamp.

Figure 1: Artika Swirl Integrated LED Floor Lamp, showcasing its unique chrome finish and spiral design.
2. Safety Information
Please read all instructions carefully before assembly and use. Keep this manual for future reference.
- Indoor Use Only: This product is designed for indoor use in dry locations. Do not expose to water or moisture.
- Electrical Safety: Ensure the power supply voltage matches the lamp's requirements (120 Volts). Always unplug the lamp from the power outlet before cleaning or performing any maintenance.
- Integrated LEDs: The LED light source is integrated and not replaceable. Do not attempt to replace the LEDs.
- Stable Placement: Place the lamp on a flat, stable surface to prevent tipping. The lamp features a heavy-duty base for stability.
- Cleaning: Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Children and Pets: Keep the lamp out of reach of small children and pets to prevent accidental damage or injury.
3. Package Contents
Verify that all components are present and undamaged before proceeding with setup.
- Artika Swirl Integrated LED Floor Lamp (1 unit)
- Power Cable with integrated foot switch (1 unit)

Figure 2: The Artika Swirl Floor Lamp as it appears with its power cable and foot switch.
4. Setup
The Artika Swirl LED Floor Lamp comes largely pre-assembled for your convenience. Follow these simple steps to set up your lamp:
- Unpack: Carefully remove all components from the packaging. Retain packaging materials for future transport or storage if needed.
- Placement: Choose a suitable indoor location with a flat, stable surface. Ensure the lamp's heavy-duty base is fully supported.
- Connect Power: Plug the power cable into a standard 120V AC electrical outlet.

Figure 3: Example of lamp placement in a living room, demonstrating its aesthetic integration.
5. Operating Instructions
Your Artika Swirl LED Floor Lamp is equipped with a convenient foot switch for easy operation and an integrated dimmer for adjustable brightness.
- Turning On/Off: Press the foot switch once to turn the lamp on. Press it again to turn the lamp off.
- Dimming: To adjust the brightness, press and hold the foot switch. The light will gradually dim or brighten. Release the switch when the desired brightness level is reached.

Figure 4: The integrated foot switch, used for both power control and dimming functions.
6. Maintenance
The Artika Swirl LED Floor Lamp requires minimal maintenance due to its integrated LED design.
- Cleaning: To clean the lamp, ensure it is unplugged from the power outlet. Gently wipe the surfaces with a soft, dry, lint-free cloth. Avoid using water, cleaning sprays, or abrasive materials, as these can damage the finish or electrical components.
- LED Lifespan: The integrated LEDs are designed for a long lifespan of approximately 50,000 hours, meaning no bulb replacement is necessary under normal use.
7. Troubleshooting
If you encounter issues with your Artika Swirl LED Floor Lamp, please refer to the following common troubleshooting steps:
- Lamp Does Not Turn On:
- Ensure the power cable is securely plugged into a working electrical outlet.
- Check if the outlet itself is functional by plugging in another device.
- Verify that the foot switch is fully pressed.
- Dimming Function Not Working:
- Ensure you are pressing and holding the foot switch to activate the dimming function, not just pressing it quickly.
- Flickering Light:
- Ensure the lamp is connected directly to a wall outlet and not to a power strip or extension cord that might be overloaded.
- Check for loose connections at the plug.
If these steps do not resolve the issue, please contact Artika customer support for further assistance.
8. Specifications
| Attribute | Detail |
|---|---|
| Model Number | FLR-SW-CCR |
| Brand | Artika |
| Light Source Type | Integrated LED |
| Wattage | 25 Watts |
| Brightness | 1950 Lumens |
| Color Temperature (CCT) | 3000 Kelvin |
| Color Rendering Index (CRI) | 80 |
| Lifespan | 50,000 Hours (minimum) |
| Voltage | 120 Volts |
| Product Dimensions (L x W x H) | 9.1" x 9.1" x 59.8" |
| Item Weight | 9.3 Pounds |
| Frame Material | Aluminum |
| Finish Type | Polished Chrome |
| Switch Type | Foot Switch with Integrated Dimmer |
| Indoor/Outdoor Usage | Indoor |
| Certification | ETL |
| UPC | 846979031931 |

Figure 5: Product dimensions for the Artika Swirl LED Floor Lamp.
9. Warranty and Support
For warranty information or technical support, please contact Artika customer service. Keep your proof of purchase for any warranty claims.
Manufacturer: Artika
Please visit the official Artika website or refer to the product packaging for the most current contact information and detailed warranty terms.





