Important Safety Information
Please read and understand all instructions before beginning assembly and installation. Failure to do so could lead to fire, electric shock, or other injuries. Keep these instructions for future reference.
- WARNING: To avoid electric shock, disconnect power at the main circuit breaker panel or main fuse box before beginning installation.
- WARNING: This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with these codes, it is recommended to have a qualified electrician perform the installation.
- Do not install any fixture closer than 6 inches from any combustible material.
- Ensure all connections are secure and properly insulated.
- Use only the specified bulb type and wattage.
Package Contents
Carefully unpack your new fixture and lay out all parts on a clear surface. Ensure all components listed below are present before discarding packaging materials.
- Island Light Fixture Assembly
- Mounting Hardware Kit (includes crossbar, mounting screws, wire nuts)
- Canopy/Ceiling Plate
- Chains (2 x 52-1/4 inches each)
- Vintage-style Bulbs (3 x 60W)
- Instruction Manual
Tools Required for Installation
- Phillips Head Screwdriver
- Flat Head Screwdriver
- Wire Strippers
- Pliers (for chain adjustment)
- Electrical Tape (optional)
- Safety Glasses
Setup and Installation
Follow these steps carefully to install your Patriot Lighting Ashtyn Island Light.
- Turn Off Power: Before starting, ensure the power to the junction box is turned off at the circuit breaker.
- Prepare Mounting: Attach the mounting crossbar to the junction box using the provided screws. Ensure it is securely fastened.
- Adjust Chain Length: The light is suspended by two chains, each measuring 52-1/4 inches. Determine the desired hanging height for your fixture. Use pliers to carefully bend open the necessary links on the chains to shorten them to your preferred length. Close the links securely after adjustment.
- Wire Connections:
- Connect the bare copper ground wire from the fixture to the green or bare copper ground wire from the junction box. Secure with a wire nut.
- Connect the white (neutral) wire from the fixture to the white (neutral) wire from the junction box. Secure with a wire nut.
- Connect the black (hot) wire from the fixture to the black (hot) wire from the junction box. Secure with a wire nut.
- Ensure all wire nuts are tightly secured and no bare wire is exposed. Wrap electrical tape around wire nuts for added security if desired.
- Attach Canopy: Carefully push the canopy up to the ceiling, covering the junction box and wiring. Secure it to the mounting crossbar using the provided screws.
- Install Bulbs: Screw the three included 60W vintage-style bulbs into the sockets. Do not overtighten.
- Restore Power: Turn the power back on at the circuit breaker and test your new light fixture.
Figure 1: Front view of the Patriot Lighting Ashtyn 3-Light Island Light.
Figure 2: Another front view of the fixture, highlighting the matte black finish and charcoal patina shades.
Figure 3: Close-up view of one of the light shades and the installed vintage-style bulb.
Operating Instructions
The Patriot Lighting Ashtyn Island Light operates like any standard ceiling light fixture. Once properly installed and wired, it can be controlled by a wall switch connected to the circuit.
- Turning On/Off: Use the wall switch to turn the light fixture on or off.
- Dimming: If connected to a compatible dimmer switch (not included), the light output can be adjusted. Ensure the bulbs used are also dimmable.
Figure 4: The Ashtyn Island Light installed above a dining table in a kitchen setting.
Maintenance
Regular maintenance will help preserve the appearance and functionality of your light fixture.
- Cleaning: Always turn off the power before cleaning. Wipe the fixture with a soft, dry cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
- Bulb Replacement: Ensure the power is off and the bulbs have cooled before attempting to replace them. Unscrew the old bulb and screw in a new 60W maximum, E26 base (standard medium base) vintage-style bulb.
Troubleshooting
If you experience issues with your light fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Power is off. 2. Loose wire connections. 3. Faulty bulb. | 1. Check circuit breaker/fuse. 2. Verify all wire connections are secure. 3. Replace bulb with a new one. |
| Light flickers. | 1. Loose bulb. 2. Loose wire connection. 3. Incompatible dimmer switch/bulb. | 1. Tighten bulb. 2. Check wire connections. 3. Ensure dimmer and bulbs are compatible. |
| Bulbs burn out quickly. | 1. Incorrect wattage bulb. 2. Voltage fluctuations. | 1. Use only 60W max bulbs. 2. Consult an electrician to check household voltage. |
If the problem persists after trying these solutions, please contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | Patriot Lighting |
| Model Number | MH321 |
| Product Dimensions | 76.25"L x 40.25"W x 24"H |
| Item Weight | 9 Pounds |
| Material | Metal |
| Color/Finish | Matte Black & Charcoal Patina |
| Number of Lights | 3 |
| Bulb Type | E26 (Medium Base) |
| Max Wattage per Bulb | 60W |
| Power Source | Corded Electric |
| Installation Type | Suspended (Island Light) |
| Indoor/Outdoor Usage | Indoor |
Warranty and Support
Patriot Lighting products are manufactured to high-quality standards and are backed by a limited warranty. For specific warranty details, please refer to the warranty card included with your purchase or visit the official Patriot Lighting website.
For technical assistance, missing parts, or any questions regarding your product, please contact Patriot Lighting customer support. Contact information can typically be found on the product packaging or the brand's official website.
