Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your PAL Lighting PAL Mini 12V Cool White LED Light with a 66-foot cord. Please read this manual thoroughly before installation and keep it for future reference.
Safety Information
WARNING: Always disconnect power before installing or servicing this product. Installation should be performed by a qualified electrician in accordance with all local and national electrical codes.
- Ensure the power supply matches the product's voltage requirements (12VAC/12VDC).
- Do not modify the product or its components.
- Keep children and pets away from the installation area.
- Inspect the cord for any damage before installation. Do not use if damaged.
Package Contents
- 1 x PAL Mini 12V Cool White LED Light (Model: 41-PCL20W20)
- 1 x 66-foot 2-wire cord (integrated)
- User Manual (this document)
Image: The PAL Mini 12V Cool White LED Light, featuring its compact LED head and a long, coiled 66-foot black two-wire cord. The cord is neatly bundled, secured with a white tie, and shows the exposed wire ends for connection.
Setup and Installation
This section outlines the general steps for installing your PAL Mini LED Light. Specific installation methods may vary based on your application (e.g., pool, spa, landscape). Consult a professional if unsure.
- Power Disconnection: Ensure all power to the installation area is turned off at the circuit breaker before beginning any work.
- Mounting Location: Choose a suitable location for the light fixture. Ensure the 66-foot cord is sufficient to reach the power source without tension.
- Wiring: Connect the two-wire cord from the PAL Mini light to a compatible 12VAC or 12VDC power supply. Ensure correct polarity if using DC power. Use appropriate waterproof connectors for outdoor or wet environments.
- Secure Fixture: Secure the light fixture in its intended position according to the specific mounting instructions for your application.
- Cable Management: Route the 66-foot cord safely, avoiding sharp edges, pinch points, or areas where it could be damaged. Secure it as needed.
- Power Connection: Once all connections are secure and the light is properly mounted, restore power to the circuit.
- Test: Verify the light functions correctly.
Operating Instructions
The PAL Mini LED Light operates by receiving power from a 12VAC or 12VDC source. It is a simple on/off light.
- Turning On: Apply 12VAC or 12VDC power to the connected wires. The light will illuminate.
- Turning Off: Disconnect the 12VAC or 12VDC power supply. The light will turn off.
- Control: This light is typically controlled by an external switch, timer, or automation system connected to its power source.
Maintenance
The PAL Mini LED Light is designed for low maintenance. Regular inspection is recommended.
- Cleaning: Periodically clean the lens of the light with a soft cloth and mild, non-abrasive cleaner to ensure optimal light output. Do not use harsh chemicals.
- Cord Inspection: Regularly inspect the entire length of the 66-foot cord for any signs of wear, cuts, or damage. If damage is found, disconnect power immediately and replace the unit.
- Connections: Ensure all electrical connections remain secure and free from corrosion.
- Winterization (if applicable): If used in a pool or spa, follow standard winterization procedures for your specific application, which may include removing the light or ensuring it is submerged.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; Incorrect wiring; Damaged unit. | Check power source and circuit breaker; Verify wiring connections; Inspect for damage and replace if necessary. |
| Light flickers. | Loose connection; Insufficient power. | Check and secure all wiring connections; Ensure power supply meets specifications. |
| Light output is dim. | Dirty lens; Voltage drop over long cable run; Faulty LED. | Clean the lens; Verify voltage at the light fixture; Contact support if LED is faulty. |
If troubleshooting steps do not resolve the issue, contact PAL Lighting customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 41-PCL20W20 |
| Light Source Type | LED |
| Light Color | Cool White |
| Voltage | 12VAC/12VDC |
| Cord Length | 66 feet |
| Wire Type | 2-Wire |
| Material | Copper (internal wiring/components) |
| Item Weight | 2.3 pounds |
| Product Dimensions | 7.4 x 7.3 x 2.6 inches (packaging/overall) |
| Manufacturer | PAL PRODUCTS, INC. |
Warranty and Support
For warranty information and technical support, please contact PAL Lighting directly. Keep your proof of purchase for warranty claims.
Manufacturer: PAL PRODUCTS, INC.
Refer to the official PAL Lighting website or your purchase documentation for the most current contact information and warranty details.
