Risco Vupoint POE IP Camera User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Risco Vupoint POE IP Camera. Please read this manual thoroughly before using the product to ensure proper functionality and safety.

Product Overview

The Risco Vupoint POE IP Camera is a high-resolution surveillance camera designed for robust security applications. It features Power over Ethernet (PoE) for simplified installation, a 4 Megapixel sensor for clear imaging, and advanced night vision capabilities.

Figure 1: Risco Vupoint POE IP Camera. This image shows a white cylindrical camera with a black lens housing and a circular mounting base. The 'RISCO' logo is visible on the side of the camera body.

Package Contents

Verify that all components are present in the package:

• 1 x Risco Vupoint POE IP Camera (Model: RVCM52P2200A)
• Mounting Hardware (screws, anchors)
• Quick Start Guide

2. Safety Information

Please observe the following safety precautions to prevent damage to the product or injury to yourself:

• Ensure the power source meets the camera's requirements (PoE).
• Do not expose the camera to extreme temperatures or humidity beyond its IP67 rating.
• Avoid direct exposure of the lens to strong light sources.
• Do not attempt to disassemble or modify the camera. Refer all servicing to qualified personnel.
• Install the camera securely to prevent it from falling.

3. Setup and Installation

Physical Installation

The Risco Vupoint POE IP Camera is designed for wall or ceiling mounting. Ensure the mounting surface is strong enough to support the camera's weight (approximately 1.06 kg / 2.34 lbs).

1. Choose a suitable location that provides the desired field of view and is within range of your network cable.
2. Use the provided mounting template (if applicable) to mark drill holes on the wall or ceiling.
3. Drill holes and insert wall anchors if necessary.
4. Secure the camera's mounting base to the surface using the provided screws.
5. Adjust the camera's angle for optimal coverage.

Network Connection (PoE)

This camera supports Power over Ethernet (PoE), simplifying wiring by delivering both power and data over a single Ethernet cable.

1. Connect one end of an Ethernet cable to the camera's RJ45 port.
2. Connect the other end of the Ethernet cable to a PoE-enabled switch or PoE injector.
3. Ensure your network is configured to provide IP addresses via DHCP or assign a static IP address to the camera if required by your system.

Initial Configuration

The camera is designed for Plug and Play installation with Risco systems. For integration with Risco Cloud™, Agility™ v3.59+, LightSYS™ v2.52+, or ProSYS™ Plus systems, follow the specific integration steps provided by Risco for your security panel.

• Risco NVR/License Requirement: Connection is mandatory via a Risco NVR, or a specific license may be required for full functionality and cloud connectivity.
• ONVIF Compatibility: The camera supports ONVIF protocol for integration with compatible third-party NVRs or video management systems. Refer to your NVR's manual for ONVIF device discovery and addition.
• SD Card Slot: Insert a compatible microSD card (not included) into the camera's SD card slot for local storage of video recordings.

4. Operating the Camera

Live View and Recording

Access the live video feed and manage recordings through your connected Risco security system's interface (e.g., Risco Cloud, NVR) or a compatible ONVIF client.

• Resolution: The camera provides a 4 Megapixel effective video resolution. Recording resolution may be set to 1080p depending on system configuration.
• Night Vision: The camera features advanced night vision with a range of up to 50 meters, automatically activating in low-light conditions.
• Motion Detection: Configure motion detection zones and sensitivity settings via your connected system for event-triggered recording and alerts.

Cloud Connectivity

For remote access and cloud-based features, ensure your camera is properly linked to your Risco Cloud account via a compatible Risco NVR or security panel.

5. Maintenance

Cleaning

To maintain optimal image quality, periodically clean the camera lens and housing.

• Use a soft, dry cloth to wipe the camera body.
• For the lens, use a lens cleaning cloth and a specialized lens cleaning solution. Do not use abrasive cleaners.

Firmware Updates

Periodically check for firmware updates through your Risco system or Risco's official website. Firmware updates can improve performance, add new features, and enhance security.

6. Troubleshooting

If you encounter issues with your Risco Vupoint POE IP Camera, refer to the following common problems and solutions:

7. Specifications

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Risco website. Keep your proof of purchase for warranty claims.

Risco Official Website: www.riscogroup.com