Lamicall Motorcycle Phone Mount Instruction Manual
Model: BP07-EU-B
Brand: Lamicall
Product Overview
The Lamicall Motorcycle Phone Mount is designed to securely hold smartphones on various handlebars, including those on motorcycles, bicycles, scooters, and even strollers. It features an upgraded quick-install handlebar clip, a metal safety lock, and 360-degree rotation for optimal viewing. The mount provides all-around protection for your device during rides.
Image: The Lamicall Motorcycle Phone Mount securely holding a smartphone, ready for use on a vehicle.
Package Contents
Please ensure all components are present before proceeding with installation:
- Lamicall Motorcycle Phone Mount (Main Unit)
- Handlebar Clip Assembly
- User Manual (this document)
Setup and Installation
Follow these steps to properly install your Lamicall Motorcycle Phone Mount:
- Attach the Handlebar Clip:
Press the button on the handlebar clip to open it. Position the clip on your desired handlebar location. Adjust the clip to fit the handlebar diameter (0.59 - 1.57 inches / 15-40mm). Tighten the screw to secure the clip firmly to the handlebar. No additional tools are required for this step.
Image: Visual guide for attaching the handlebar clip, showing the press button, adjustment, and tightening screw.
- Mount the Phone Holder:
Ensure the phone holder is securely attached to the ball joint of the handlebar clip. The ball joint allows for angle adjustment.
- Insert Your Phone:
Gently pull open the phone clamp. Place your smartphone into the mount, ensuring it is centered and held by the four corners and back silicone pads. The mount is compatible with 4.7 - 6.8 inch phones, with a maximum thickness of 0.59 inches.
Image: Demonstrating one-hand operation to mount a phone into the holder.
- Engage Metal Safety Lock:
After placing your phone, slide the metal safety lock located at the back of the mount to the locked position. This provides additional security, especially during high-speed cycling or on rough terrain.
Image: Detail of the metal safety lock, ensuring the phone remains secure.
Operating Instructions
Using your Lamicall Motorcycle Phone Mount is straightforward:
- Adjust Viewing Angle:
The mount features a 360-degree rotation ball joint. Loosen the adjustment knob slightly, rotate your phone to the desired horizontal or vertical viewing angle, and then tighten the knob to secure it. This allows for convenient GPS navigation, calling, or music playback.
Image: A cyclist utilizing the 360-degree rotation feature for optimal phone viewing.
- One-Hand Operation:
The quick-release mechanism allows for easy mounting and removal of your phone with one hand. Simply press the release button to expand the clamps, insert or remove your phone, and the clamps will automatically secure it (ensure the metal safety lock is disengaged before removal).
- Phone Protection:
The four corners and back of the phone holder are equipped with non-slip silicone pads. These pads protect your cell phone from scratches and prevent slipping, even on rough roads. The upgraded up and down linkage phone clamp holds your smartphone tightly.
Image: Detailed view of the cushioned pads and secure lock, highlighting the protective features.
Maintenance
To ensure the longevity and optimal performance of your Lamicall Motorcycle Phone Mount, follow these maintenance guidelines:
- Cleaning: Wipe the mount with a soft, damp cloth to remove dust and dirt. Avoid using harsh chemicals or abrasive cleaners, as these can damage the materials.
- Inspection: Periodically check all screws and joints to ensure they are tight and secure. If any part feels loose, tighten it carefully.
- Storage: When not in use for extended periods, store the mount in a cool, dry place away from direct sunlight.
- Silicone Pads: Ensure the silicone pads are clean and free from debris to maintain optimal grip and prevent scratches to your phone.
Troubleshooting
If you encounter any issues with your phone mount, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Phone feels loose in the mount. | Metal safety lock not engaged; phone not properly seated; phone too small for the mount. | Ensure the metal safety lock is engaged. Re-seat the phone firmly. Verify phone size is within 4.7-6.8 inches and thickness is under 0.59 inches. |
| Mount slides on the handlebar. | Handlebar clip not tightened sufficiently; handlebar diameter outside specified range. | Tighten the handlebar clip screw firmly. Ensure your handlebar diameter is between 0.59 - 1.57 inches (15-40mm). |
| Difficulty rotating the phone. | Adjustment knob is too tight. | Loosen the adjustment knob slightly before attempting to rotate the phone. Tighten once the desired angle is achieved. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | BP07-EU-B |
| Product Dimensions | 5.46 x 3.56 x 4.3 inches |
| Item Weight | 9 ounces |
| Compatible Phone Size | 4.7 - 6.8 inches |
| Max Phone Thickness | 0.59 inches |
| Handlebar Diameter Compatibility | 0.59 - 1.57 inches (15-40mm) |
| Mounting Type | Handlebar |
| Special Features | 360 Degree Rotation, Metal Safety Lock, One-Hand Operation, Quick Release Button, Rubber Pads Protection |
| Color | Black |
| Manufacturer | Lamicall |
Note: Specifications are subject to change without prior notice.
Warranty and Support
Information regarding product warranty and customer support is not provided within this manual. Please refer to the product packaging or the official Lamicall website for details on warranty coverage and how to contact customer support.
For further assistance, you may visit the Lamicall Store on Amazon.