1. Introduction
This manual provides detailed instructions for the assembly, operation, maintenance, and troubleshooting of your Young 200 lbs. 2 Bike Rack. Designed for secure and convenient transportation of up to two bicycles, this platform-style hitch mount rack is compatible with a variety of vehicles equipped with a 2-inch hitch receiver. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
2. Safety Information
Your safety and the safety of others are paramount. Adhere to all warnings and instructions to prevent injury or damage.
- WARNING: DO NOT exceed 120 lbs of capacity when this bike rack is installed behind an RV.
- WARNING: DO NOT use this bike carrier for transporting or carrying items or materials other than bicycles.
- WARNING: Using the bike rack for rough off-road terrain is not recommended.
- Ensure all bolts and fasteners are securely tightened before each use.
- Always check that bikes are properly secured and stable before driving.
- Be aware of the increased length and width of your vehicle when the bike rack is installed.
3. Package Contents
Most parts of your Young 2 Bike Rack come pre-assembled for ease of installation. Please verify that all components listed below are present and undamaged:
- Main hitch receiver assembly
- Vertical support mast
- Adjustable wheel cradles (2 sets)
- Padded frame hooks (2)
- Wheel straps (4)
- Hitch pin and clip
- All necessary hardware (bolts, washers, nuts)
- Instruction Manual
4. Setup and Installation
Assembly of the bike rack typically takes 30-40 minutes and requires a wrench. The design allows for straightforward installation and removal from your vehicle's hitch receiver.
4.1 Assembling the Rack
Follow the detailed instructions provided in the included Instruction Manual for step-by-step assembly. Ensure all bolts are tightened securely. The rack is designed for a 2-inch hitch receiver.
Figure 4.1: The fully assembled Young 2 Bike Rack, ready for installation on a vehicle's hitch receiver.
4.2 Installing on Vehicle Hitch
Insert the main hitch assembly into your vehicle's 2-inch hitch receiver. Align the pinholes and insert the provided hitch pin, securing it with the clip. The rack includes a dampening pin to minimize wobble during transit. For easier alignment, you may mark the hitch hole with tape.
Figure 4.2: Close-up of the stable-grip mega cradle and padded hooks, highlighting the anti-wobble and anti-scratch design for secure bike transport.
5. Operating Instructions
The Young 2 Bike Rack is designed for easy loading and unloading of bicycles.
5.1 Loading Bicycles
Slide your bicycles onto the rack, ensuring the wheels rest securely in the adjustable wheel cradles. The top bar of the rack goes across the bike frame. Adjust the wheel cradles to fit different bike lengths and tire widths up to 5 inches. Secure the bike frames with the soft padded hooks and use the provided wheel straps to firmly hold the tires in place. Loading two bikes typically takes about 2 minutes.
Figure 5.1: Illustration showing the adjustable sliders and vertical mast for adapting to various bike lengths and tire widths up to 5 inches, with a maximum wheelbase of 58 inches.
Figure 5.2: The Young 2 Bike Rack with two bicycles securely mounted on the rear of a vehicle, demonstrating its compact profile.
5.2 Folding and Tilting Features
The rack features a folding design for compact storage when not in use. It also has a quick-release tilting function that allows access to your vehicle's trunk without removing the bikes. Note that tilting may require removing a pin for full functionality.
Figure 5.3: The bike rack in its folded-up position, demonstrating how it can be stored compactly on the vehicle.
Figure 5.4: The bike rack tilted back, providing easy access to the vehicle's trunk without needing to unload the bicycles.
6. Maintenance
To ensure the longevity and safe operation of your bike rack, perform regular maintenance:
- Periodically inspect all bolts, nuts, and pins for tightness. Tighten as necessary.
- Clean the rack with mild soap and water, then dry thoroughly to prevent rust.
- Check the condition of the padded hooks and wheel straps for wear and tear. Replace if damaged.
- Store the rack in a dry place when not in use.
7. Troubleshooting
If you encounter issues with your bike rack, consider the following:
- Excessive Wobble: Ensure the dampening hitch pin is fully inserted and tightened. Verify that the rack is properly seated in the hitch receiver.
- Difficulty with Hitch Pin: Some users have noted that the threaded hitch locking pin can be cumbersome for frequent removal. Ensure the threads are clear and aligned.
- Bike Instability: Double-check that the padded hooks are securely fastened over the bike frames and that all wheel straps are tightly secured. The wheel cradles should be adjusted to fit your specific bike's wheelbase and tire width.
- Wheel Bracket Issues: In rare cases, the internal tightening mechanism of the wheel brackets may experience issues. Ensure proper installation and avoid exceeding the stated load capacity. If issues persist, contact customer support.
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Young Electric |
| Model Number | 10104095 |
| Color | Black |
| Item Dimensions (L x W x H) | 39.37 x 51.45 x 40.31 inches |
| Load Capacity | 200 Pounds (Total) |
| Mounting Type | 2 inch hitch receiver |
| Item Weight | 41.6 pounds |
| UPC | 805089680392 |
| Special Features | Foldable, Hitch Mount |
9. Warranty and Support
Your Young 2 Bike Rack comes with a 1-Year Warranty. If anything ever goes wrong with your hitch mounted bike rack, please contact our 24H Service Team for assistance. For further support or inquiries, please refer to the contact information provided on the product packaging or the official Young Electric website.
