LEDONE Remote Control User Manual

1. Introduction

This manual provides comprehensive instructions for the LEDONE Remote Control, designed for use with Motion Detection, UFO High Bay, Parking Lot Light, and Linear High Bay Lights (specifically HD406VRH Sensor compatible). This remote enhances convenience and control over your lighting systems, allowing for customization of various settings to optimize performance and energy efficiency in commercial spaces.

2. Product Features

• Direct control over LED high bay light processes.
• Four pre-programmed fixed scene modes for automatic settings.
• Controls UFO High Bay lights and integrated motion detection sensors.
• Customizable brightness and motion sensor settings.
• Includes essential functions: On/Off, Auto mode, and Reset for straightforward operation.

3. Setup

3.1 Battery Installation

The LEDONE Remote Control requires 'A' type batteries (not included). To install:

1. Locate the battery compartment cover on the back of the remote control.
2. Slide the cover open in the direction indicated by the arrow.
3. Insert the 'A' batteries, ensuring correct polarity (+ and -) as marked inside the compartment.
4. Replace the battery compartment cover until it clicks securely into place.

3.2 Initial Connection

The remote control is designed to work seamlessly with compatible LEDONE UFO High Bay and Linear High Bay Lights equipped with HD406VRH sensors. No complex pairing is typically required; the remote should function upon battery installation and being within range of the compatible light fixture.

4. Operating Instructions

Familiarize yourself with the remote control layout:

Figure 1: LEDONE Remote Control Layout

4.1 Basic Functions

• ON/OFF: Press to toggle the connected light fixture on or off.
• Auto Mode: Activates the automatic operation mode, utilizing the sensor's default or previously set parameters.
• Reset: Resets all settings on the connected light fixture to their factory default values.
• Brightness (+/-): Adjusts the light output intensity.

4.2 Advanced Settings

The remote allows for precise customization of sensor and lighting parameters:

• Start: Initiates the application of selected settings.
• Memory: Saves the current custom settings for quick recall.
• Apply: Applies the settings stored in memory or the currently selected custom settings.

Detection Range

Select the desired motion detection sensitivity:

• 25%, 50%, 75%, 100%: Choose the percentage of the sensor's maximum detection range.

Hold Time

Sets the duration the light remains at full brightness after motion is detected and before dimming or turning off:

• 5s, 30s, 1min, 3min, 5min, 10min, 15min, 30min: Select the hold time in seconds or minutes.

Stand-by Dimming Level

Determines the light output level during the stand-by period (after hold time and before turning off):

• 10%, 20%, 30%, 50%: Set the dimming percentage.

Stand-by Period

Sets the duration the light remains at the stand-by dimming level before turning off completely:

• 0s, 10s, 30s, 1min, 5min, 10min, 30min, +∞: Select the stand-by period. '+∞' indicates the light will remain at the stand-by dimming level indefinitely.

Daylight Sensor

Configures the ambient light threshold at which the motion sensor will activate the light:

• 2Lux, 10Lux, 30Lux, 50Lux, 80Lux, 120Lux: Light will only turn on if ambient light is below the selected Lux level.
• Disable: The daylight sensor is deactivated, and the light will respond to motion regardless of ambient light.

Test (2s)

Activates a 2-second test mode to verify sensor functionality and current settings.

5. Maintenance

To ensure optimal performance and longevity of your LEDONE Remote Control:

• Cleaning: Wipe the remote with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Battery Replacement: Replace batteries when the remote's response becomes sluggish or inconsistent. Always use new 'A' type batteries.
• Storage: Store the remote in a cool, dry place away from direct sunlight and extreme temperatures.
• Avoid Moisture: Do not expose the remote to water or high humidity.

6. Troubleshooting

If you encounter issues with your LEDONE Remote Control, refer to the following common problems and solutions:

• Remote not responding:
  • Check battery installation and replace batteries if necessary.
  • Ensure there are no obstructions between the remote and the light fixture's sensor.
  • Verify that the light fixture is powered on and functioning correctly.
• Settings not applying:
  • Ensure you are pressing the 'Apply' or 'Start' button after making changes.
  • Confirm the remote is within effective range of the light fixture.
  • Try resetting the light fixture using the 'Reset' button on the remote, then re-apply settings.
• Limited range:
  • Replace batteries with fresh ones.
  • Ensure no strong interference sources (e.g., other wireless devices) are nearby.

7. Specifications

8. Warranty and Support

LEDONE is committed to providing quality lighting solutions and customer satisfaction. Our products are designed for optimal performance and safety. For any inquiries, technical assistance, or warranty information, please contact LEDONE customer service. LEDONE is based in California, offering worry-free services for our products.