Introduction
This instruction manual provides comprehensive guidance for the safe and proper installation and operation of your PERLESMITH TV Wall Mounts, including both the PSMTK1 Tilting Mount and the PSMFK12 Full Motion Mount. Please read this manual thoroughly before beginning installation to ensure correct setup and to prevent damage or injury.
These mounts are designed to securely hold your television, optimizing viewing angles and saving space. The PSMTK1 is a low-profile tilting mount, while the PSMFK12 offers full motion articulation.
Image: The PERLESMITH PSMTK1 Tilting TV Wall Mount (top) and the PSMFK12 Full Motion TV Wall Mount (bottom) with included hardware.
Important Safety Precautions
- Do not install on drywall alone. Ensure mounting into wood studs, solid concrete, or brick walls.
- Verify your TV's VESA mounting hole pattern, weight, and port location before purchase and installation.
- Do not exceed the maximum weight capacity: 115 lbs (52 kg) for PSMTK1 and 77 lbs (35 kg) for PSMFK12.
- Always use the included hardware. If you have any doubts about the installation, consult a qualified professional.
- Keep children and pets away during installation.
- Ensure all connections are secure before releasing the TV.
Setup and Installation
Pre-Installation Checklist
- Confirm TV size compatibility: PSMTK1 for 23"-60" TVs, PSMFK12 for 26"-60" TVs.
- Check VESA compatibility:
- PSMTK1: 75x75mm, 100x75mm, 100x100mm, 200x100mm, 200x200mm, 300x200mm, 300x300mm, 400x300mm, 400x400mm.
- PSMFK12: 100x100mm, 100x200mm, 200x100mm, 200x200mm, 300x200mm, 300x300mm, 400x200mm, 400x400mm.
- Locate wall studs (for wood stud installation) or ensure suitable concrete/brick wall.
- Gather necessary tools (e.g., drill, level, screwdriver, stud finder).
General Installation Steps (Applies to both models)
- Attach Brackets to TV: Secure the vertical TV brackets to the back of your television using the appropriate screws and spacers from the hardware kit. Ensure they are centered and firmly attached.
- Mark Wall Position: Determine the desired height for your TV. Hold the wall plate against the wall and mark the drilling locations. Use a level to ensure accuracy.
- Drill Pilot Holes: Drill pilot holes at the marked locations. Use a stud finder for wood studs. For concrete or brick, use a masonry drill bit and insert anchors.
- Mount Wall Plate: Secure the wall plate to the wall using the provided lag bolts. Ensure it is level and tightly fastened.
- Hang TV: Carefully lift the TV with the attached brackets and hook it onto the wall plate. Ensure the brackets are properly seated.
- Secure TV: For the PSMTK1, use the pull cords to engage the safety locks. For the PSMFK12, ensure the arms are extended and adjusted as needed.
Specific Installation Notes for PSMTK1 (Tilting Mount)
Image: Visual guide showing the simplified 3-step installation process for the PSMTK1 tilting mount, including attaching brackets, mounting the wall plate, and hanging the TV with a pull cord lock and release mechanism.
The PSMTK1 mount is designed for quick and easy installation, often completed within 12 minutes. It features an enhanced hook for drop-free use and an anti-drop buckle for secure attachment. The low-profile design holds the TV just 1.2 inches from the wall.
Image: The PSMTK1 tilting mount highlighting its 115 lbs maximum weight capacity, 1.5x taller plate for stronger support, and features like the enhanced hook and anti-drop buckle for secure installation.
This mount can be installed on 16-inch wood studs, solid concrete, or brick walls. It is crucial not to install it on drywall alone.
Image: Diagram illustrating the compatibility of the PSMTK1 tilting mount with three wall types: wood studs (16.0" max, 8" min spacing), solid concrete, and brick walls. A warning indicates not to install on drywall alone.
Specific Installation Notes for PSMFK12 (Full Motion Mount)
Image: The PERLESMITH PSMFK12 Full Motion TV Wall Mount, showcasing its articulating arms and the assortment of screws, anchors, and washers included for installation.
The PSMFK12 mount features a sturdy and strong articulating arm, designed for durability and stability. It has been cycle-tested over 6,000 times for proven reliability and is UL listed (UL file number E522707).
Image: A graphic demonstrating the PERLESMITH PSMFK12 Full Motion TV Mount undergoing reliability testing, indicating it has been cycle-tested over 6,000 times and is UL listed, ensuring its strength and durability.
This mount supports single stud mounting for flexible placement, making installation easier and more adaptable to various room layouts.
Image: The PERLESMITH PSMFK12 Full Motion TV Mount shown installed on a single wall stud, emphasizing its flexible placement capability and ease of installation.
Operating Your TV Mount
PSMTK1 Tilting Mount Operation
The PSMTK1 allows for a tilt adjustment of up to 7 degrees forward. This feature is designed to reduce glare from lights or windows and improve your viewing angle, especially if the TV is mounted higher than eye level.
Image: A television mounted with the PERLESMITH PSMTK1 tilting mount, demonstrating its ability to tilt forward by 7 degrees to reduce glare and optimize viewing for TVs between 23 and 60 inches.
To adjust the tilt, gently push or pull the bottom of the TV to achieve the desired angle. The mount will hold its position once set.
PSMFK12 Full Motion Mount Operation
The PSMFK12 offers full motion capabilities, allowing you to extend, swivel, and tilt your TV for optimal viewing from almost any angle in the room. This is particularly useful for large rooms or multi-purpose spaces.
Image: The PERLESMITH PSMFK12 Full Motion TV Mount showcasing its wide compatibility for TVs between 26 and 60 inches, with a weight capacity of 77 lbs and various VESA patterns from 100x100mm to 400x400mm.
- Extension: Gently pull the TV away from the wall to extend the articulating arm.
- Swivel: Rotate the TV left or right along the swivel axis to change the horizontal viewing angle.
- Tilt: Adjust the vertical tilt by loosening the tilt knobs (if present) on the TV brackets, setting the desired angle, and then re-tightening.
Always move the TV smoothly and avoid sudden jerks. Ensure cables are not pinched or strained during adjustments.
Maintenance
- Regular Inspection: Periodically check all screws and bolts to ensure they remain tight and secure. Over time, vibrations or adjustments can cause them to loosen.
- Cleaning: Use a soft, dry cloth to wipe down the mount. Avoid abrasive cleaners or solvents that could damage the finish.
- Joint Lubrication (PSMFK12): If the articulating arm joints become stiff, a small amount of silicone-based lubricant can be applied to the moving parts. Do not use oil-based lubricants.
- Cable Management: Ensure TV cables are neatly routed and not under tension, especially when adjusting the full motion mount.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| TV not level after installation. | Wall plate or TV brackets not perfectly level. | Carefully adjust the wall plate or TV brackets. Some mounts have post-installation leveling features. |
| Mount feels unstable. | Loose bolts, incorrect wall type, or exceeding weight capacity. | Re-tighten all bolts. Verify installation on appropriate wall type. Ensure TV weight is within limits. If unsure, consult a professional. |
| Difficulty tilting/swiveling (PSMFK12). | Joints are stiff or friction bolts are too tight. | Apply a small amount of silicone lubricant to the joints. Loosen friction bolts slightly if applicable (refer to specific model instructions). |
| TV not securely locked (PSMTK1). | Safety pull cords not engaged. | Ensure the pull cords are fully engaged to lock the TV brackets onto the wall plate. |
Product Specifications
| Feature | PSMTK1 (Tilting Mount) | PSMFK12 (Full Motion Mount) |
|---|---|---|
| Brand | PERLESMITH | |
| Mounting Type | Wall Mount | Wall Mount |
| Movement Type | Tilt | Articulating, Tilt |
| Material | Alloy Steel | |
| Color | Black | |
| Compatible TV Sizes | 23 - 60 inches | 26 - 60 inches |
| Maximum Weight Capacity | 115 lbs (52 kg) | 77 lbs (35 kg) |
| VESA Compatibility | 75x75mm to 400x400mm | 100x100mm to 400x400mm |
| Low Profile Distance (from wall) | 1.2 inches | (Varies with extension) |
| Maximum Tilt Angle | 7 degrees forward | 15 degrees (overall, includes tilt) |
| UL Certified | N/A | Yes (UL file number E522707) |
Warranty and Support
PERLESMITH products are designed for durability and reliability. For specific warranty information regarding your TV wall mount, please refer to the warranty card included with your product or visit the official PERLESMITH website.
If you encounter any issues during installation or operation, or if you have questions about your product, please contact PERLESMITH customer support. You can often find contact details on the product packaging, the PERLESMITH brand store on Amazon, or their official website.
Online Support: For additional resources, FAQs, and troubleshooting guides, please visit the PERLESMITH Brand Store on Amazon.
