Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Herdio 6.5-inch Bluetooth Ceiling Speakers with In-Wall Amplifier. This system is designed to deliver high-fidelity audio for various indoor environments, including home theaters, bathrooms, living rooms, kitchens, and offices. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.
Package Contents
Verify that all items listed below are included in your package:
- 1x Wall Mount Bluetooth Amplifier
- 1x AC Adapter
- 2x Screws
- 2x 6.5-inch In-Ceiling Speakers
- 2x Speaker Wires
- 2x User Manuals (one for amplifier, one for speakers)
Setup
This section guides you through the physical installation and wiring of your Herdio ceiling speaker system.
1. Amplifier Installation
The in-wall amplifier is designed for flush mounting in a standard wall plate size. Ensure you have appropriate wiring access before proceeding.
- Prepare the Wall: Use the provided template (if applicable) to mark and cut an opening in the wall for the amplifier.
- Connect Power Cable: Connect the 12V DC power cable to the designated two-pin connector on the back of the amplifier module.
- Connect Audio Cable: Connect the audio cable to the three-pin connector on the back of the amplifier module.
- Secure Amplifier: Insert the amplifier module into the wall opening and secure it using the provided screws.
- Attach Faceplate: Place the decorative faceplate over the installed amplifier and secure it.
2. Speaker Installation
The ceiling speakers are designed for flush mounting. Ensure you have appropriate ceiling space and wiring access.
- Mark Cutout: Use the provided cutout template to mark the desired location for each speaker in the ceiling.
- Cut Opening: Carefully cut the circular opening in the ceiling according to the marked template. The cutout diameter is approximately 8.07 inches (20.5 cm).
- Remove Grille: Gently remove the magnetic grille from the front of each speaker.
- Connect Speaker Wires: Connect the speaker wires to the spring-loaded terminals on the back of each speaker. Ensure correct polarity: red wire to positive (+) terminal, black wire to negative (-) terminal.
- Insert Speaker: Insert the speaker into the ceiling opening. The mounting clamps will automatically engage.
- Tighten Clamps: Use a screwdriver to tighten the screws on the front baffle of the speaker. This will rotate the mounting clamps and secure the speaker firmly in place.
- Replace Grille: Reattach the magnetic grille to the speaker.
3. Wiring Diagram
Connect the speaker wires from the ceiling speakers to the amplifier terminals. Ensure correct polarity for both speakers (red to +, black to -).
4. Power Connection
Connect the AC adapter to a standard 120V power outlet and then plug the DC end into the amplifier's power input. The power LED on the amplifier will illuminate.
Video: This video demonstrates the unboxing, wiring, Bluetooth pairing, and installation process for the Herdio 6.5-inch Bluetooth Ceiling Speakers Set.
Operating Instructions
Learn how to use your Herdio ceiling speaker system.
1. Power On/Off and Volume Control
Turn the knob on the amplifier clockwise to power on the unit and increase the volume. Turn it counter-clockwise to decrease volume and power off. You will hear an audible drop sound when powering on.
2. Bluetooth Pairing
After powering on, the blue Bluetooth indicator light will flash, indicating it is in pairing mode. On your smart device (phone, tablet, etc.), search for available Bluetooth devices and select 'Herdio'. Once connected, the blue light will remain solid.
3. Input Selection
Use the input selection switch on the amplifier to choose between Bluetooth (BT), Auxiliary (AUX), or Microphone (MIC) input modes.
4. USB Functionality
The USB port functions as a flash memory reader for media playback and also provides a charging port for your devices (5V/1A).
5. Microphone Input
Connect a microphone to the 1/4-inch MIC IN jack for paging or voice applications.
Maintenance
To ensure the longevity and optimal performance of your Herdio ceiling speakers and amplifier, follow these maintenance guidelines:
- Cleaning: Use a soft, dry cloth to clean the amplifier faceplate and speaker grilles. Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage the finish.
- Dust Removal: Periodically use a soft brush or a low-power vacuum with a brush attachment to gently remove dust from the speaker grilles.
- Environmental Conditions: Ensure the speakers and amplifier are installed in environments free from excessive moisture, extreme temperatures, and direct sunlight. The product is not waterproof.
- Wiring Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion or damage.
Troubleshooting
If you encounter issues with your Herdio ceiling speaker system, refer to the following common problems and solutions:
- No Power:
- Ensure the AC adapter is securely plugged into a working power outlet and the amplifier's DC input.
- Check if the power knob on the amplifier is turned clockwise to the 'ON' position.
- Verify that the power outlet is functional by plugging in another device.
- No Sound from Speakers:
- Confirm that the speaker wires are correctly connected to both the speakers and the amplifier, observing proper polarity (+ to +, - to -).
- Ensure the volume knob on the amplifier is turned up.
- Check the input selection switch on the amplifier to ensure the correct source (BT, AUX, MIC) is selected.
- If using Bluetooth, ensure your device is paired and playing audio.
- If using AUX or MIC, ensure the external device is connected and functioning correctly.
- Bluetooth Connection Issues:
- Ensure the amplifier is in Bluetooth pairing mode (blue light flashing).
- Make sure your Bluetooth device is within the 30+ feet wireless range.
- Forget the 'Herdio' device from your smart device's Bluetooth settings and attempt to re-pair.
- Restart both the amplifier and your Bluetooth device.
- Distorted Sound:
- Reduce the volume on both the amplifier and your audio source device.
- Check speaker wire connections for any loose strands or short circuits.
- Ensure the audio source is not overdriven or producing distorted signals.
Specifications
| Brand | Herdio |
| Model Name | HCS 818 |
| Speaker Type | Woofer, Tweeter |
| Speaker Size | 6.5 Inches |
| Speaker Maximum Output Power | 320 Watts |
| Impedance | 8 Ohms |
| Frequency Response | 20 KHz (Note: This is likely the upper limit, typical range is broader) |
| Connectivity Technology | Auxiliary, Bluetooth, USB |
| Wireless Communication Technology | Bluetooth |
| Bluetooth Range | 30 Feet |
| Input Voltage | 120 Volts |
| Power Source | Corded Electric |
| Mounting Type | Flush Mount, Ceiling Mount |
| Product Dimensions (Amplifier) | 9.25"D x 9.25"W x 4.13"H (Note: This dimension seems to be for the speaker, not the amplifier. Amplifier is typically smaller, as shown in images.) |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Is Waterproof | FALSE (Not Water Resistant) |
| Item Weight | 9.08 pounds (Total package weight) |
Warranty Information
The Herdio 6.5-inch Bluetooth Ceiling Speakers with In-Wall Amplifier comes with a Limited Warranty. For specific details regarding warranty coverage, duration, and claims process, please refer to the warranty card included in your package or contact Herdio customer support directly.
Support
For further assistance, technical support, or inquiries regarding your Herdio product, please visit the official Herdio website or contact their customer service department. Contact information can typically be found on the product packaging or on the Herdio website.