Chuancheng Accessory Kit Instruction Manual

Main Brush

The main brush is a combo roller brush designed for superior pick-up of pet hair, dirt, dust, and debris. It is effective on various floor types including hardwood, carpet, and tile.

Image: Detailed view of the main brush, highlighting its ABS plastic ends, rubber blade, and bristle brush sections. Dimensions are 165mm / 6.4 inches in length.

Image: Illustration of the combo roller brush effectively cleaning different floor surfaces, including hardwood, carpet, and tile.

Side Brushes

The side brushes feature a three-arm design with TPU arms and bristle brushes, designed to sweep debris from edges and corners into the robot's cleaning path.

Image: Close-up of the side brush, detailing its TPU arms and bristle brush components. Dimensions are 60mm / 2.36 inches in length for the arms.

HEPA Filters

These high-efficiency HEPA filters are designed to capture 99.5% of dirt, dust, pet hair, and small debris, improving air quality during cleaning. Each filter consists of a pleated HEPA material and a foam pre-filter.

Image: Visual representation of the high-efficiency HEPA filter's capability to filter out fine particles like dirt, dust, and pet hair.

Image: Detailed view of the HEPA filter, showing its pleated structure and dimensions (137mm / 5.39 inches long, 54mm / 2.13 inches wide). It also shows the foam pre-filter.

Image: Important notice illustrating two types of dust boxes and indicating which filter design is suitable for each, ensuring correct fit.

Mop Cloths

The mop cloths are made from fine microfiber, designed for effective wet cleaning. They are washable and reusable, offering an environmentally friendly alternative to disposable options.

Image: The mop cloth submerged in water, illustrating its washable and reusable nature for multiple cleaning cycles.

Image: Front and back views of the mop cloth, highlighting its fine microfiber material and dimensions (275mm / 10.83 inches long, 107mm / 4.21 inches wide).

Installing the Main Brush

1. Flip the robot vacuum over to access the main brush compartment.
2. Press the release tabs on the main brush cover and remove it.
3. Lift out the old main brush.
4. Insert the new main brush, ensuring the ends align with the slots in the robot.
5. Replace the main brush cover and press firmly until it clicks into place.

Installing Side Brushes

1. Flip the robot vacuum over.
2. Gently pull the old side brushes upwards to remove them.
3. Align the new side brushes with the posts on the robot and push down until they click securely into place. Ensure the correct brush (left/right, if applicable) is installed in the corresponding slot.

Installing HEPA Filters

1. Open the dust bin cover on your robot vacuum.
2. Remove the dust bin.
3. Open the dust bin's filter compartment.
4. Remove the old HEPA filter and foam pre-filter.
5. Insert the new foam pre-filter, then the new HEPA filter, ensuring it sits flush within the compartment. Refer to the filter compatibility image in the Component Overview section to ensure you have the correct filter type for your dust bin.
6. Close the filter compartment and reinsert the dust bin into the robot.

Attaching Mop Cloths

1. Locate the water tank or mopping plate on your robot vacuum.
2. Attach the mop cloth to the designated area on the water tank or mopping plate, typically using Velcro or a sliding mechanism. Ensure it is securely fastened.
3. Fill the water tank if necessary before reattaching it to the robot.

Cleaning the Main Brush

Remove the main brush as described in the installation section. Use the cleaning tool (often included with your robot vacuum) to remove tangled hair and debris from the brush bristles and rubber blades. You can also rinse the brush under running water if it's heavily soiled, ensuring it is completely dry before reinstallation.

Cleaning Side Brushes

Remove the side brushes. Use a soft cloth or the cleaning tool to wipe away dust and debris. If hair is tangled around the base, carefully cut it away. If the bristles are bent, refer to the troubleshooting section.

Cleaning/Replacing HEPA Filters

Tap the HEPA filter gently over a trash can to dislodge dust. The foam pre-filter can be rinsed with water and air-dried completely. The pleated HEPA filter should not be washed. It is recommended to replace the HEPA filters every 2 to 3 months, depending on usage frequency, to maintain filtration efficiency.

Cleaning Mop Cloths

After each use, remove the mop cloth from the water tank/mopping plate. The mop cloth can be washed directly with water and reused. It is designed to withstand more than 50-60 cleaning cycles, making it a durable and eco-friendly option.

Edge Brush Deformation

If the edge brushes appear deformed upon receipt or after prolonged use, you can immerse them in hot water for a few minutes. This can help the bristles return to their original shape. Allow them to cool and dry completely before reinstallation.