SmartHeart Automatic Blood Pressure Monitor

Important Safety Information

Please read this instruction manual thoroughly before using your SmartHeart Blood Pressure Monitor. Keep this manual for future reference.

• Consult your physician before using this device if you have any medical conditions.
• Do not use this device for diagnosis or treatment of any health problem or disease.
• Measurements taken with this device are for reference only. Always consult a healthcare professional for interpretation of results.
• Keep out of reach of children.
• Do not disassemble or attempt to repair the unit.
• Use only approved accessories and parts.

Package Contents

• SmartHeart Automatic Blood Pressure Monitor Unit
• Wide-Range Arm Cuff (fits arm circumference 8.6 in. - 16.5 in. / 22 cm - 42 cm)
• Instruction Manual
• Storage Bag

Product Overview

Familiarize yourself with the components of your blood pressure monitor.

Figure 1: SmartHeart Automatic Blood Pressure Monitor with its wide-range arm cuff and storage bag. The monitor features a large digital display and two buttons: MEM and START.

Figure 2: Detailed view of the monitor's display. It shows systolic (SYS), diastolic (DIA) pressure in mmHg, and pulse rate per minute. A hypertension indicator is visible on the left side of the screen.

Figure 3: Intelligent Inflation Technology. This feature uses previous measurement history to determine the optimal inflation level, resulting in faster and more comfortable readings.

Figure 4: Wide-Range Arm Cuff details. The cuff fits arm circumferences from 8.6 to 16.5 inches (22-42 cm), features a traditional D-ring style, soft fabric, and hook & loop closure for a comfortable fit. It is not made with natural rubber latex.

Setup

1. Battery Installation

Open the battery compartment cover on the back of the unit. Insert four (4) AA alkaline batteries, ensuring correct polarity (+/-). Close the cover securely.

2. Connecting the Arm Cuff

Insert the air tube connector from the arm cuff firmly into the air jack on the left side of the monitor unit.

3. Setting Date and Time (if applicable)

Refer to the specific instructions in your manual for setting the date and time, usually involving pressing the 'MEM' button in a specific sequence while the unit is off or in setup mode.

Operating Instructions

Preparing for Measurement

• Avoid eating, drinking alcohol, smoking, or exercising for at least 30 minutes before measurement.
• Rest for at least 5 minutes before taking a measurement.
• Sit upright with your back supported and feet flat on the floor.
• Place your arm on a flat surface so the cuff is at heart level.
• Ensure the cuff is applied directly to bare skin, not over clothing.

Applying the Arm Cuff

1. Slide your left arm through the cuff loop. The air tube should run down the inside of your arm.
2. Position the cuff so the bottom edge is approximately 1 inch (2-3 cm) above your elbow.
3. Wrap the cuff snugly around your arm, securing it with the hook and loop fastener. Ensure it is not too tight or too loose.

Taking a Measurement

1. With the cuff correctly applied and the unit connected, press the START button.
2. The cuff will automatically inflate. Remain still and silent during the measurement.
3. Once the measurement is complete, the cuff will deflate, and your systolic pressure, diastolic pressure, and pulse rate will be displayed on the screen.
4. The unit will automatically store the reading in its memory.
5. Press the START button again to turn off the unit, or it will automatically shut off after 1 minute of inactivity.

Memory Functions

The SmartHeart monitor stores previous readings for easy review.

Viewing Stored Readings

• From the OFF state, press the MEM button.
• The most recent reading will be displayed first.
• Press the MEM button repeatedly to scroll through older readings.
• The unit will display the average of the last three readings (if available) before showing individual readings.

Clearing Memory

To clear all stored readings, press and hold the MEM button for approximately 5 seconds while in memory recall mode until "CLR" or "---" appears on the display, indicating memory has been cleared.

Maintenance and Care

• Clean the monitor unit and cuff with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
• Store the unit in its storage bag in a cool, dry place, away from direct sunlight and extreme temperatures.
• Remove batteries if the unit will not be used for an extended period to prevent leakage.
• Do not drop or subject the unit to strong impacts.
• Regularly check the air tube and cuff for any signs of damage or wear.

Troubleshooting

Specifications

• Model: 01-539WR
• Measurement Method: Oscillometric
• Measurement Range:
  • Pressure: 0-300 mmHg
  • Pulse: 40-199 beats/minute
• Accuracy:
  • Pressure: ±3 mmHg
  • Pulse: ±5% of reading
• Cuff Size: Wide-Range Arm Cuff (fits arm circumference 8.6 in. - 16.5 in. / 22 cm - 42 cm)
• Memory: Stores up to 99 readings
• Power Source: 4 x AA batteries (not included)
• Automatic Shut-off: Approximately 1 minute after last operation
• Operating Conditions: 50°F - 104°F (10°C - 40°C), 15-90% RH non-condensing
• Storage Conditions: -4°F - 140°F (-20°C - 60°C), 10-95% RH non-condensing
• Weight: Approximately 8 ounces (excluding batteries)
• Manufacturer: Veridian Healthcare
• UPC: 845717009201

Warranty and Support

SmartHeart products are manufactured to strict quality standards. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official SmartHeart website. Keep your purchase receipt as proof of purchase for warranty claims.

Note: Warranty terms may vary by region.