1. Overview
The Cooler Master Hyper 212 EVO V2 is a high-performance CPU air cooler designed for efficient heat dissipation and quiet operation. It features an upgraded SickleFlow 120 PWM fan, Direct Contact Technology with four copper heat pipes, and an asymmetrical design to ensure broad compatibility with various motherboard components and PC cases.
Key Features:
- SickleFlow 120 Fan: Optimized blade design for improved airflow and static pressure.
- Direct Contact Technology: Four copper heat pipes directly contact the CPU for superior heat transfer.
- Asymmetrical Heat Pipe Design: Provides 100% RAM clearance for unhindered memory installation.
- Optimal Air Flow: Stacked fin array minimizes resistance for effective heat dissipation.
- Quiet Operation: Engineered to reduce vibration for a silent computing experience.
2. Setup and Installation
Before beginning installation, ensure your system is powered off and disconnected from the power source. Refer to your motherboard manual for specific instructions regarding CPU cooler installation and component placement.
2.1 Pre-Installation Checks
- RAM Clearance: The asymmetrical heat pipe design ensures 100% RAM clearance. Verify that the cooler will not obstruct your memory modules.
- Chassis Clearance: Ensure your PC case has adequate space for the cooler. The Hyper 212 EVO V2 has a height of approximately 154mm.
- CPU Socket Compatibility: Confirm your CPU socket type is supported. This cooler supports Intel LGA1700, LGA1200, LGA1151, LGA1150, LGA1155, LGA1156, LGA2066, LGA2011-v3, LGA2011 and AMD AM4, AM3+, AM3, AM2+, AM2, FM2+, FM2, FM1 sockets.
2.2 Installation Steps (General)
- Prepare CPU: Clean the CPU surface thoroughly to remove any old thermal paste.
- Apply Thermal Paste: Apply a small amount of thermal paste (pea-sized dot) to the center of the CPU's integrated heat spreader (IHS).
- Install Backplate (if required): Depending on your socket, install the appropriate backplate behind the motherboard.
- Attach Mounting Brackets: Secure the correct mounting brackets to the heatsink base according to your CPU socket type.
- Mount Heatsink: Carefully place the heatsink onto the CPU, aligning the mounting screws with the backplate or motherboard holes. Tighten screws in a diagonal pattern until snug, ensuring even pressure. Do not overtighten.
- Attach Fan: Secure the SickleFlow 120 fan to the heatsink using the provided fan clips. Ensure the fan is oriented to push air through the heatsink towards the rear exhaust of your PC case.
- Connect Fan Cable: Connect the 4-pin PWM fan cable to the CPU_FAN header on your motherboard.
3. Operating Instructions
The Cooler Master Hyper 212 EVO V2 operates automatically once installed and connected to the motherboard's CPU_FAN header. The PWM (Pulse Width Modulation) function allows the motherboard to control the fan speed based on CPU temperature, optimizing for both cooling performance and noise levels.
- Fan Speed: The SickleFlow 120 fan operates within a range of 650-1800 RPM (rotations per minute) ± 10%.
- Noise Level: The maximum noise level is rated at 27 dBA, ensuring quiet operation under typical loads.
- Airflow: The fan provides up to 62 CFM (cubic feet per minute) of airflow.
- Air Pressure: The fan generates up to 2.5 mmH2O of static pressure, effective for pushing air through the heatsink fins.
4. Maintenance
Regular maintenance helps ensure optimal performance and longevity of your CPU cooler.
- Dust Cleaning: Periodically (e.g., every 3-6 months), power off your PC and use compressed air to clean dust from the fan blades and heatsink fins. Dust buildup can impede airflow and reduce cooling efficiency.
- Thermal Paste Check: Over time, thermal paste can dry out. Consider reapplying thermal paste every 2-3 years, or if you notice a significant increase in CPU temperatures. This requires removing the cooler, cleaning old paste, and applying new paste.
- Fan Inspection: Ensure the fan is securely attached and spinning freely without obstruction. Check the fan cable connection to the motherboard.
5. Troubleshooting
If you encounter issues with your Cooler Master Hyper 212 EVO V2, consider the following troubleshooting steps:
- High CPU Temperatures:
- Verify that the heatsink is securely mounted and making proper contact with the CPU.
- Check if thermal paste was applied correctly and is not dried out.
- Ensure the fan is spinning and connected to the CPU_FAN header.
- Confirm adequate airflow within your PC case (e.g., proper case fan setup).
- Excessive Noise:
- Inspect the fan for any obstructions (cables, dust buildup) that might be causing rattling or grinding noises.
- Ensure the fan is securely attached to the heatsink and not vibrating against other components.
- Check fan speed settings in your motherboard's BIOS/UEFI or operating system software.
- Installation Difficulties:
- Double-check that you are using the correct mounting brackets for your CPU socket.
- Refer to the installation steps and diagrams carefully. Do not force components.
6. Specifications
| Feature | Detail |
|---|---|
| Model Number | RR-2V2E-18PK-R2 |
| Dimensions (L x W x H) | 120mm x 80mm x 154mm (4.72"L x 3.15"W x 4.72"H) |
| Material | Copper (Heat Pipes), Aluminum (Fins) |
| Heat Pipes | 4 Direct Contact |
| Fan Type | SickleFlow 120 PWM Fan |
| Fan Speed | 650-1800 RPM ± 10% |
| Fan Airflow | 62 CFM |
| Fan Air Pressure | 2.5 mmH2O |
| Fan Noise Level | 27 dBA (Max) |
| Power Connector | 4-Pin PWM |
| Rated Voltage | 12V DC |
| Rated Current | 0.15A |
| Power Consumption | 1.8W |
| CPU Socket Compatibility | Intel: LGA1700, LGA1200, LGA1151, LGA1150, LGA1155, LGA1156, LGA2066, LGA2011-v3, LGA2011 AMD: AM4, AM3+, AM3, AM2+, AM2, FM2+, FM2, FM1 |
7. Warranty and Support
The Cooler Master Hyper 212 EVO V2 CPU Air Cooler is covered by a manufacturer's warranty. For specific warranty terms, duration, and to access technical support, please visit the official Cooler Master website or contact their customer service department. Keep your proof of purchase for warranty claims.