1. Introduction
This manual provides instructions for the CHUNGHOP Replacement Remote Control, designed for use with various Humax Foxsat HDR Freesat Box models. This remote control is a direct replacement and requires no programming or pairing for immediate use.
2. Product Overview
The CHUNGHOP replacement remote control is designed to replicate the functionality of your original Humax Foxsat HDR Freesat Box remote. It features an ergonomic design for comfortable handling.
Figure 2.1: Front, side, and back views of the CHUNGHOP replacement remote control.
Figure 2.2: Dimensions of the remote control, approximately 23.7cm (9.3 inches) in length, 5.1cm (2 inches) in front width, and 2.3cm (0.9 inches) in side thickness.
2.1 Compatible Models
This remote control is compatible with the following Humax Foxsat HDR Freesat Box models:
- RM-F01
- RM-F04
- RM-E06
- FOXSAT-HDR
- HDR-1000GB
- HDR-1TB
- HDR-320GB
- HDR-500GB
- HD-FOX-T2
- HDR-FOX-T2
- HDR-FOX-T2-1TB
- HDR-FOX-T2-500GB
- IHDR-5200C
- IHRD-5050C
- IRHD-5100C
3. Setup
3.1 Battery Installation
To begin using your remote control, you must install two AAA batteries. Batteries are not included with the remote control.
- Locate the battery compartment cover on the back of the remote control.
- Slide the cover downwards or press the latch (if present) to open the compartment.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Replace the battery compartment cover by sliding it back into place until it clicks securely.
Figure 3.1: Battery compartment for two AAA batteries.
3.2 Initial Use
Once batteries are installed, the remote control is ready for immediate use. No programming or pairing is required. Simply point the remote control towards your Humax Foxsat HDR Freesat Box and operate as you would with the original remote.
4. Operation
The CHUNGHOP replacement remote control functions identically to the original remote for your Humax Foxsat HDR Freesat Box. All buttons are pre-configured to perform their respective actions.
4.1 Basic Functions
- Power Button: Turns the device on or off.
- Number Buttons (0-9): For direct channel input.
- Volume Up/Down: Adjusts the audio volume.
- Channel Up/Down: Changes the television channel.
- Navigation Buttons (Up, Down, Left, Right, OK): For menu navigation and selection.
- Media Control Buttons (Play, Pause, Stop, Rewind, Fast Forward): For controlling media playback.
- Guide Button: Accesses the electronic program guide.
- Menu Button: Opens the main menu.
- Exit/Back Button: Returns to the previous screen or exits a menu.
Refer to your Humax Foxsat HDR Freesat Box user manual for specific functions of each button if you require detailed information beyond basic operation.
5. Troubleshooting
5.1 Remote Control Not Responding
- Check Batteries: Ensure that two fresh AAA batteries are correctly installed with the proper polarity (+/-). Weak or dead batteries are the most common cause of remote control malfunction.
- Line of Sight: Ensure there is a clear line of sight between the remote control and the infrared receiver on your Humax Foxsat HDR Freesat Box. Obstructions can block the signal.
- Distance: Operate the remote control within a reasonable distance from the device.
- Interference: Bright lights or other electronic devices emitting infrared signals can sometimes interfere with the remote control's operation. Try moving away from potential sources of interference.
5.2 Specific Button Not Working
- If only a specific button is not working, try pressing it firmly. If the issue persists, it might indicate a fault with the remote control.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | CHUNGHOP |
| Compatible Models | Humax Foxsat HDR Freesat Box (RM-F01, RM-F04, RM-E06, FOXSAT-HDR, HDR-1000GB, HDR-1TB, HDR-320GB, HDR-500GB, HD-FOX-T2, HDR-FOX-T2, HDR-FOX-T2-1TB, HDR-FOX-T2-500GB, IHDR-5200C, IHRD-5050C, IRHD-5100C) |
| Connectivity Technology | Infrared |
| Controller Type | Button Control |
| Special Feature | Ergonomic Design |
| Max Number of Supported Devices | 1 |
| Batteries Required | 2 x AAA (not included) |
7. Maintenance
To ensure the longevity and proper functioning of your remote control:
- Keep the remote control clean by wiping it with a soft, dry cloth.
- Avoid exposing the remote control to extreme temperatures, direct sunlight, or moisture.
- Do not drop the remote control or subject it to strong impacts.
- Remove batteries if the remote control will not be used for an extended period to prevent leakage.
8. Support
For any questions or assistance regarding your CHUNGHOP Replacement Remote Control, please contact the manufacturer or seller. Support inquiries are typically answered within 24 hours.
You can often find contact information on the product packaging or through the retailer where the item was purchased.
