1. Introduction
This manual provides instructions for the safe and effective operation of your Amplim Non-Contact Digital Infrared Forehead Thermometer. This device is designed for measuring body temperature from the forehead without physical contact, and can also measure surface temperatures. It is suitable for use with babies, children, and adults.
The non-invasive, touch-free design offers a hygienic and comfortable method for temperature measurement compared to traditional rectal, oral, ear, or armpit thermometers.
Image 1.1: The Amplim Non-Contact Digital Infrared Forehead Thermometer is suitable for all ages, including babies, teens, adults, and the elderly.
2. Product Overview
Familiarize yourself with the components of your Amplim Non-Contact Digital Infrared Forehead Thermometer:
Image 2.1: Labeled components of the Amplim Non-Contact Digital Infrared Forehead Thermometer. Key parts include the sensor, color-coded LCD display, control buttons (ON/SCAN, Up/Memory, Down/Memory, Light, MODE), and the battery compartment.
- Sensor: Detects infrared radiation to measure temperature.
- Color-coded LCD Display: Shows temperature readings and other indicators. The display changes color to indicate temperature status (green for normal, yellow for elevated, red for high).
- ON/SCAN Button: Powers on the device and initiates a temperature scan.
- Up/Memory Button: Navigates through stored memory readings or adjusts settings.
- Down/Memory Button: Navigates through stored memory readings or adjusts settings.
- Light Button: Controls the display backlight.
- MODE Button: Switches between Forehead (Body) mode and Surface mode, and accesses settings.
- Battery Lid: Covers the battery compartment.
3. Setup
3.1 Battery Installation
The thermometer requires two AAA batteries for operation. To install or replace batteries:
- Locate the battery lid on the handle of the thermometer.
- Slide the battery lid open.
- Insert two AAA batteries, ensuring the correct polarity (+/-) as indicated inside the compartment.
- Close the battery lid securely.
The thermometer will perform a self-test upon first power-on or after battery replacement.
4. Operating Instructions
4.1 Taking a Forehead Temperature (Body Mode)
To measure body temperature:
- Ensure the thermometer is in 'Body' mode. If not, press the MODE button to switch.
- Hold the thermometer approximately 0.3 to 1.2 inches (1-3 cm) from the center of the forehead.
- Press the ON/SCAN button.
- The temperature reading will appear on the display within approximately 1 second, accompanied by an audible beep.
Image 4.1: The thermometer can be used in Forehead Mode for body temperature or Surface Mode for object temperatures.
4.2 Taking a Surface Temperature (Surface Mode)
To measure the temperature of an object's surface:
- Press the MODE button to switch to 'Surface' mode.
- Point the thermometer at the object whose surface temperature you wish to measure.
- Press the ON/SCAN button.
- The surface temperature will be displayed.
4.3 Understanding the Color-Coded Display
The LCD display changes color to provide a quick visual indication of the temperature reading:
- Green: Indicates a normal temperature (e.g., 89.6-99.0°F / 32.0-37.2°C).
- Yellow: Indicates an elevated temperature (e.g., 99.1-100.3°F / 37.3-37.9°C).
- Red: Indicates a high temperature, potentially a fever (e.g., 100.4-109.4°F / 38.0-43.0°C). An audible alarm will also sound in this range.
Image 4.2: The color-coded display provides an immediate visual cue for temperature status.
4.4 Changing Temperature Units (°C/°F)
To switch between Celsius and Fahrenheit:
- With the thermometer powered on, press and hold the MODE button for a few seconds until the unit symbol starts flashing.
- Use the Up/Memory or Down/Memory buttons to select either °C or °F.
- Press the MODE button again to confirm your selection and exit the setting.
4.5 Memory Function
The thermometer stores the last 25 or more temperature readings. To access stored readings:
- With the thermometer powered on, briefly press the Up/Memory or Down/Memory button.
- Each press will cycle through the stored readings, from most recent to oldest.
5. Maintenance
5.1 Cleaning and Care
To ensure accurate readings and prolong the life of your thermometer:
- Wipe the thermometer body with a soft, damp cloth.
- For the sensor lens, use a cotton swab lightly moistened with alcohol. Allow to dry completely before use.
- Do not immerse the thermometer in water or any other liquid.
- Avoid using abrasive cleaning agents or thinners.
- Store the thermometer in a cool, dry place away from direct sunlight and extreme temperatures.
5.2 Battery Replacement
When the low battery indicator appears on the display, replace both AAA batteries as described in Section 3.1. Always use new batteries of the same type.
6. Troubleshooting
If you encounter issues with your thermometer, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No display or device won't turn on. | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity. |
| Inaccurate readings. | Sensor dirty, incorrect distance, or environmental factors. | Clean the sensor. Ensure correct distance (0.3-1.2 inches) from forehead. Avoid strong air currents or direct sunlight during measurement. Allow thermometer to acclimatize to room temperature for 30 minutes if moved from a different environment. |
| Display shows 'Lo' or 'Hi'. | Temperature is outside the measurable range. | Ensure the thermometer is used within its specified operating temperature range. For body temperature, ensure the subject is not in an extreme environment. |
| Display shows 'Err'. | System error. | Remove batteries, wait 1 minute, then reinsert. If the error persists, contact customer support. |
7. Specifications
- Model Names: Amplim AE2 and Amplim F2
- Item Model Number: AE2
- Brand: Amplim
- Display Type: Digital, Color-coded LCD
- Connectivity Technology: Infrared
- Special Feature: Audible Alarm for high temperatures
- Measurement Time: Approximately 1 second
- Measurement Distance: 0.3 - 1.2 inches (1-3 cm)
- Memory Storage: 25+ readings
- Temperature Units: Celsius (°C) or Fahrenheit (°F)
- Power Source: 2 x AAA Batteries (included)
- Outer Material: Plastic
- Product Care Instructions: Wipe Clean
8. Safety Information
- This thermometer is intended for household use. Consult a medical professional for interpretation of temperature readings, especially for infants or if you have health concerns.
- Do not attempt to disassemble or repair the device yourself.
- Keep the device out of reach of children and pets.
- Avoid dropping the thermometer or subjecting it to strong impacts.
- Do not use the thermometer in environments with strong electromagnetic interference.
- Dispose of batteries and the device according to local environmental regulations.
9. Warranty and Support
Amplim products are manufactured to high-quality standards and undergo factory testing. For warranty information, technical support, or any questions regarding your Amplim Non-Contact Digital Infrared Forehead Thermometer, please refer to the contact information provided with your product packaging or visit the official Amplim website.
You can also visit the Amplim Store on Amazon for more information and to contact the seller directly.
