Nolan N880000270056 Flip-Up Helmet User Manual

Introduction

This manual provides essential information for the proper use, maintenance, and care of your Nolan N880000270056 Flip-Up Helmet. Please read this manual thoroughly before using your helmet to ensure maximum safety and to prolong the life of your product. This helmet is designed for motorcycle and powersports use, featuring a thermoplastic shell, an ultra-wide Lexan visor, and an adjustable VPS sun visor.

Figure 1: Front view of the Nolan N880000270056 Flip-Up Helmet. This image displays the helmet in its closed position, highlighting the main visor and the overall design.

Safety Information

Your safety is paramount. Always wear a helmet that fits correctly and is securely fastened. A helmet cannot protect against all foreseeable impacts. For maximum protection, the helmet must be properly fitted and securely fastened on the wearer's head in accordance with the manufacturer's instructions.

• Fitment: Ensure the helmet fits snugly and does not move freely on your head.
• Retention System: Always fasten the chin strap securely.
• Visibility: Keep visors clean and free from scratches. Replace damaged visors immediately.
• Damage: Never use a helmet that has sustained an impact, even if no visible damage is apparent. Replace it immediately.
• Chemicals: Avoid contact with petroleum products, cleaning agents, paints, adhesives, or other solvents. These can cause damage to the helmet materials without visible signs.

Setup

1. Unpacking

Carefully remove the helmet from its packaging. Inspect the helmet for any signs of damage that may have occurred during shipping. Retain the packaging for future storage or transport.

2. Visor Installation/Adjustment

The Nolan N880000270056 comes with a Lexan ultra-wide visor. Ensure it is securely attached to the helmet's pivot mechanism. If removal is necessary for cleaning or replacement, refer to the pivot mechanism instructions (usually a quick-release system). Align the visor tabs with the helmet's pivot points and press firmly until it clicks into place.

3. VPS Sun Visor Adjustment

The helmet features an adjustable dark tinted VPS sun visor with UV 400 protection. This internal visor can be lowered or raised using a slider mechanism located on the side of the helmet. Move the slider to deploy or retract the sun visor as needed. The automatic retraction mechanism ensures the sun visor retracts fully when released.

4. Fitment

Proper fitment is crucial for safety and comfort. The helmet should fit snugly around your entire head, without any pressure points. It should not move when you shake your head. If the helmet moves, it is too large. If it causes discomfort or pain, it is too small. Try different sizes until you find the correct fit.

1. Place the helmet on your head, ensuring it sits level.
2. Fasten the chin strap securely. It should be tight enough that you cannot pull the helmet off your head by pulling from the rear.
3. With the chin strap fastened, try to rotate the helmet from side to side and front to back. There should be minimal movement.

Operating

1. Wearing the Helmet

Always hold the chin straps apart when putting on or taking off the helmet to avoid unnecessary stress on the retention system and to ease the process.

2. Operating the Flip-Up Mechanism

As a flip-up style helmet, the chin bar can be raised. Locate the release button or lever, typically positioned at the front center of the chin bar. Press the button and lift the chin bar upwards until it locks into its open position. To close, press the release button again (if required by design) and lower the chin bar firmly until it clicks and locks into the closed position. Ensure it is fully latched before riding.

3. Operating the Main Visor

The main Lexan ultra-wide visor can be opened to various positions or fully raised. Use the tab located on the visor to lift or lower it. Ensure the visor is fully closed when riding at speed or in adverse weather conditions to protect your eyes and face.

4. Operating the Internal Sun Visor

The VPS sun visor is operated by a slider on the side of the helmet. Push the slider forward to deploy the sun visor and backward to retract it. The sun visor is intended for use in bright conditions and should be retracted in low light or at night to maintain optimal visibility.

Maintenance

1. Cleaning the Helmet Shell

Clean the thermoplastic shell with a soft cloth, warm water, and mild soap. Avoid abrasive cleaners, solvents, or petroleum-based products, as these can damage the helmet's finish and structural integrity. Rinse thoroughly and air dry.

2. Cleaning Visors

Both the main Lexan visor and the VPS sun visor should be cleaned with warm water and a soft microfiber cloth. For stubborn dirt, use a mild soap solution. Do not use abrasive materials or chemical cleaners, as they can scratch or damage the scratch-resistant coating. Air dry or gently pat dry with a clean, soft cloth.

3. Liner Removal and Cleaning (if applicable)

While specific instructions for liner removal are not provided, many Nolan helmets feature removable and washable interior padding. If your helmet has this feature, carefully detach the liner components according to the helmet's internal instructions (often indicated by small labels or clips). Hand wash with mild soap and water, then air dry completely before reinserting.

4. Storage

Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from dust and scratches. Do not store the helmet near chemicals or solvents.

Troubleshooting

• Visor Fogging: Ensure proper ventilation. If persistent, consider anti-fog treatments or a Pinlock insert (if compatible and available).
• Chin Bar Not Latching: Check for obstructions. Ensure the mechanism is clean. Apply a small amount of silicone lubricant if stiff. Do not force it.
• Sun Visor Sticking: Clean the sun visor and its tracks. Ensure no debris is obstructing its movement.
• Helmet Too Tight/Loose: Re-evaluate fitment. A helmet that is too tight or too loose compromises safety. Consider trying a different size or replacement padding if available.

Specifications

Warranty and Support

Nolan helmets are manufactured to high standards and typically come with a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and claim procedures, please refer to the warranty card included with your helmet or visit the official Nolan website. For technical support, spare parts, or service inquiries, please contact your authorized Nolan dealer or the Nolan customer service department.

Contact Information: Please refer to the official Nolan website or your purchase documentation for the most current contact details.