1. Introduction
The Godox MoveLink M2 is a compact 2-person digital wireless microphone system designed for content creators, including vloggers, journalists, and videographers. It provides a reliable and easy-to-use solution for recording high-quality audio with cameras, smartphones, and audio recorders. This system operates on a 2.4 GHz frequency band, offering a stable wireless connection for clear sound capture.
2. What's in the Box
Upon unpacking, please ensure all the following items are present:
- 2 x MoveLink M2 Transmitters (TX) with built-in microphones
- 1 x MoveLink M2 Two-Channel Receiver (RX)
- 2 x Lavalier Microphones
- 2 x Furry Wind Caps for Transmitters
- 1 x 3.5mm TRS to 3.5mm TRS Cable (for cameras)
- 1 x 3.5mm TRS to 3.5mm TRRS Cable (for smartphones/tablets)
- 3 x USB Type-C Charging Cables
- 1 x Charging Case
- User Manual (this document)
3. Product Overview
Familiarize yourself with the components of the Godox MoveLink M2 system.

Figure 1: Godox MoveLink M2 Wireless Microphone System showing one receiver unit on the left and two transmitter units on the right. Each unit is compact, gray, and features a display screen and various ports/buttons on its sides.
3.1 Transmitter (TX)
- Built-in Microphone: Omnidirectional, for direct audio capture.
- 3.5mm Input Jack: For connecting external lavalier microphones.
- Power Button: On/off and pairing.
- Gain Control Buttons: Adjust microphone input level.
- USB Type-C Port: For charging and power supply.
- Clip: For attaching to clothing.
- Display Screen: Shows battery status, signal strength, and audio level.
3.2 Receiver (RX)
- 3.5mm Output Jack: Connects to camera, smartphone, or audio recorder.
- 3.5mm Headphone Jack: For real-time audio monitoring.
- Power Button: On/off and pairing.
- Volume Control Buttons: Adjust output volume.
- USB Type-C Port: For charging and power supply.
- Belt Clip/Shoe Mount: For attaching to camera hot shoe or belt.
- Display Screen: Shows battery status, signal strength for both channels, and audio levels.
4. Setup
4.1 Initial Charging
Before first use, fully charge the transmitters and receiver using the provided USB Type-C cables and charging case. The units will indicate charging status on their displays.
4.2 Powering On/Off
Press and hold the power button on each unit (TX and RX) for approximately 2 seconds to power on or off.
4.3 Pairing the Units
- Ensure both the transmitter(s) and receiver are powered on.
- Briefly press the pairing button on the transmitter(s) and then on the receiver. The units will automatically search and pair.
- A successful connection is indicated by a solid signal icon on the display screens.
4.4 Connecting to a Recording Device
- For Cameras (DSLR/Mirrorless): Use the 3.5mm TRS to 3.5mm TRS cable. Connect one end to the receiver's 3.5mm output and the other end to your camera's microphone input.
- For Smartphones/Tablets: Use the 3.5mm TRS to 3.5mm TRRS cable. Connect one end to the receiver's 3.5mm output and the other end to your smartphone's headphone/microphone jack.
- For Audio Recorders: Use the appropriate 3.5mm cable (TRS or TRRS depending on the recorder's input type) to connect the receiver's output to the recorder's input.
5. Operating Instructions
5.1 Using the Built-in Microphone
Attach the transmitter directly to your clothing using its clip, ensuring the built-in microphone is facing towards your mouth. For outdoor use, attach the furry wind cap to reduce wind noise.
5.2 Using External Lavalier Microphones
Plug the 3.5mm connector of the lavalier microphone into the 3.5mm input jack on the transmitter. Clip the lavalier microphone to your clothing, typically 6-8 inches below your chin, and conceal the transmitter.
5.3 Adjusting Audio Levels
- Transmitter Gain: Use the gain control buttons on the transmitter to adjust the input sensitivity. Monitor the audio level on the transmitter's display to avoid clipping (distortion).
- Receiver Output Volume: Use the volume control buttons on the receiver to adjust the output level sent to your recording device. It is recommended to set the camera/recorder input level to a moderate setting and fine-tune with the receiver's volume.
5.4 Monitoring Audio
Connect headphones to the receiver's 3.5mm headphone jack to monitor the audio in real-time. This allows you to ensure clear sound capture and detect any issues during recording.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the units. Do not use liquid cleaners or solvents.
- Storage: Store the system in a cool, dry place, away from direct sunlight and extreme temperatures.
- Battery Care: For optimal battery life, avoid fully discharging the batteries frequently. Recharge them regularly, even if not in use for extended periods.
- Avoid Moisture: Keep the units away from water and high humidity to prevent damage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No audio output |
|
|
| Distorted audio |
|
|
| Interference/Dropouts |
|
|
| Short battery life |
|
|
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | MoveLink M2 |
| Brand | GODOX |
| Microphone Form Factor | Microphone System |
| Polar Pattern | Omnidirectional (built-in mic) |
| Number of Channels | 2 |
| Connectivity Technology | 2.4 GHz Digital Wireless, USB |
| Connector Type | 3.5 mm Jack, USB Type-C |
| Compatible Devices | Camera, Smartphone, Audio Recorder, Camcorder |
| Power Source | Battery Powered (Internal Lithium-ion) |
| Battery Life | Up to 6 hours (approx.) |
| Operating Range | Up to 164' (50m) line-of-sight |
9. Warranty and Support
For warranty information and technical support, please refer to the warranty card included with your product or visit the official GODOX website. Keep your purchase receipt as proof of purchase for warranty claims.