1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your BRILONER LED Ceiling Light, Model 3482-014. This modern ceiling fixture features an integrated LED board, a fabric shade with a unique starlight effect, and provides neutral white light suitable for various indoor environments.
Please read this manual thoroughly before installation and retain it for future reference.
Image 1.1: BRILONER LED Ceiling Light, showcasing its grey/silver fabric shade and starlight effect.
2. Safety Instructions
- Electrical Safety: Always disconnect the main power supply before attempting any installation, maintenance, or repair work. Ensure the power is off at the circuit breaker or fuse box.
- Qualified Personnel: If you are unsure about electrical installations, consult a qualified electrician.
- Indoor Use Only: This product is rated IP20, meaning it is protected against solid objects larger than 12.5mm but has no protection against water. It is designed exclusively for indoor use in dry environments. Do not install in bathrooms, outdoors, or areas with high humidity.
- Mounting Surface: Ensure the mounting surface is structurally sound and can support the weight of the fixture.
- Handling: Handle the fixture with care to avoid damage to the fabric shade or internal components.
- Light Source: The LED light source is integrated and not user-replaceable. Do not attempt to open the LED module.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- 1 x BRILONER LED Ceiling Light (Model 3482-014)
- Mounting hardware (screws, wall plugs)
- Instruction Manual
4. Setup & Installation
Follow these steps carefully to install your ceiling light. Ensure power is disconnected before starting.
- Prepare for Installation: Turn off the main power supply to the installation area at the circuit breaker.
- Remove Old Fixture (if applicable): Carefully remove any existing light fixture, noting the wiring connections.
- Mark Mounting Points: Hold the mounting bracket (usually located inside the lamp) against the ceiling at the desired installation spot. Use a pencil to mark the drilling points.
- Drill Holes: Drill holes at the marked points using an appropriate drill bit for your ceiling material. Insert wall plugs if necessary.
- Secure Mounting Bracket: Attach the mounting bracket to the ceiling using the provided screws. Ensure it is firmly secured.
- Wire Connections: Connect the electrical wires from the ceiling to the terminals on the light fixture. Typically, this involves connecting live (L), neutral (N), and earth (E) wires. Ensure connections are secure and correctly matched according to local electrical codes.
- Attach the Fixture: Carefully align the ceiling light with the mounting bracket and secure it in place. This usually involves twisting or screwing the lamp body onto the bracket.
- Restore Power: Once the fixture is securely installed and all connections are checked, restore power at the circuit breaker.
Image 4.1: Dimensional diagram of the ceiling light, showing a diameter of 320mm and a height of 120mm.
5. Operating Instructions
The BRILONER LED Ceiling Light is designed for simple operation via a standard wall switch.
- Turning On/Off: Use your existing wall switch to turn the light fixture on or off.
- Starlight Effect: The integrated LED board creates a starlight effect through the fabric shade, providing a decorative light pattern in addition to the main illumination.
Image 5.1: The ceiling light illuminated, demonstrating the neutral white 4000K light and the decorative starlight effect.
6. Maintenance
To ensure the longevity and optimal performance of your BRILONER LED Ceiling Light, follow these maintenance guidelines:
- Cleaning: Disconnect power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the exterior of the fixture. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or fabric.
- No User-Serviceable Parts: The LED light source is integrated and cannot be replaced by the user. If the LED module fails, the entire fixture may need to be replaced.
- Inspection: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician.
7. Troubleshooting
If you encounter issues with your BRILONER LED Ceiling Light, refer to the following common troubleshooting steps:
- Light Does Not Turn On:
- Check if the main power supply to the fixture is on.
- Verify that the wall switch is in the 'ON' position.
- Ensure all electrical connections are secure and correctly wired. If unsure, consult a qualified electrician.
- Check your household circuit breaker or fuse box for tripped breakers or blown fuses.
- Flickering Light:
- Ensure all wiring connections are tight.
- Verify that the voltage supply is stable and within the specified range (230 Volts).
If these steps do not resolve the issue, contact customer support or a qualified electrician.
8. Specifications
| Model Number | 3482-014 |
| Brand | BRILONER |
| Dimensions (Diameter x Height) | 32 x 12 cm (12.6 x 4.7 inches) |
| Weight | 670 grams (1.48 lbs) |
| Power Consumption | 12 Watts |
| Voltage | 230 Volts (AC) |
| Luminosity | 1200 Lumens |
| Color Temperature | 4000K (Neutral White) |
| Lifespan | Approx. 25,000 hours |
| Material | Plastic, Fabric |
| IP Rating | IP20 (Indoor use only) |
| Installation Method | Flush Mount |
| Special Features | Energy-saving, Starlight Effect |
9. Warranty & Support
For information regarding warranty coverage, please refer to the documentation provided with your purchase or visit the official BRILONER website.
If you require technical assistance or have questions not covered in this manual, please contact BRILONER customer support through their official channels.
10. Official Product Videos
No official product videos from the seller are available for this model at this time.
