1. Introduction
This manual provides essential information for the proper use, fitting, and maintenance of your Giro Escape MIPS Adult Urban Cycling Helmet. Please read these instructions carefully before using your helmet to ensure maximum safety and performance. This helmet is designed for urban cycling and incorporates advanced safety features.
2. Safety Information
Your Giro Escape MIPS helmet is engineered to reduce the risk of head injury during a fall or impact. However, no helmet can protect against all possible impacts. For your safety, always follow these guidelines:
- Proper Fit: A helmet must fit properly to provide effective protection. Ensure the helmet is snug, level on your head, and the straps are securely fastened.
- MIPS Technology: The Multi-Directional Impact Protection System (MIPS) is designed to reduce rotational forces that can result from certain impacts. This system allows the helmet to slide relative to the head, redirecting energy.
- Helmet Replacement: A helmet involved in an impact should be replaced immediately, even if there is no visible damage. The protective materials may be compromised.
- Visibility: The integrated LED lights enhance your visibility to others, but do not replace the need for additional lights or reflective gear, especially in low-light conditions.
- Chemical Exposure: Do not expose the helmet to solvents, paints, or decals, as these can damage the helmet's materials and compromise its protective capabilities.
3. Product Overview
The Giro Escape MIPS helmet combines urban style with advanced protection and visibility features. Key components and technologies include:
- MIPS (Multi-Directional Impact Protection System): An integrated low-friction layer designed to reduce rotational motion transferred to the brain from angled impacts.
- Integrated LED Lights: Front (white) and rear (red) rechargeable LED lights for enhanced visibility.
- Roc Loc Sport MIPS Fit System: A dial-based retention system for easy, secure, and comfortable fit adjustment.
- Hybrid Construction: Merges a durable ABS plastic shell with an EPS liner for robust protection.
- Ventilation: Strategically placed vents for airflow and comfort.
Image 3.1: Front-left view of the Giro Escape MIPS helmet, showcasing its sleek design and integrated front light.
Image 3.2: Side view of the helmet, showing the MIPS sticker and the rear integrated LED light.
Image 3.3: Rear view of the helmet, highlighting the integrated red LED light for increased visibility.
4. Setup
4.1. Sizing and Fit
A properly fitted helmet is crucial for protection. Follow these steps to ensure a correct fit:
- Measure Your Head: Use a flexible tape measure to measure the circumference of your head, just above your eyebrows and ears.
- Consult Size Chart: Compare your measurement to the size chart below. The Giro Escape MIPS helmet is available in Small (51-55cm), Medium (55-59cm), and Large (59-63cm).
- Try On the Helmet: Place the helmet squarely on your head, ensuring it sits level and covers your forehead. It should feel snug all around your head.
Image 4.1: Giro Helmet Sizing Chart, showing head circumference ranges for Small, Medium, and Large sizes.
Image 4.2: Side view of the helmet on a person, demonstrating proper helmet positioning.
4.2. Adjusting the Roc Loc Sport MIPS Fit System
The Roc Loc Sport MIPS system allows for fine-tuning the helmet's fit:
- Locate the dial at the rear of the helmet.
- Turn the dial clockwise to tighten the fit system, making the helmet snugger.
- Turn the dial counter-clockwise to loosen the fit system.
- Adjust until the helmet feels secure without causing discomfort or pressure points. The helmet should not move excessively when you shake your head.
4.3. Strap Adjustment
The chin strap system ensures the helmet stays in place:
- Fasten the buckle securely under your chin.
- Adjust the strap length so that it is snug but not uncomfortably tight. You should be able to fit one or two fingers between the strap and your chin.
- Adjust the side sliders to ensure the straps form a 'V' shape just below your ears.
4.4. Integrated LED Lights
The helmet features integrated front (white) and rear (red) LED lights for enhanced visibility.
Charging:
- Locate the micro USB charging port, typically covered by a rubber flap, on the helmet.
- Connect the helmet to a power source using a micro USB cable (not included).
- A charging indicator light will show the charging status (e.g., red for charging, green for fully charged).
Operation:
- Press the power button (usually located near the lights) to cycle through light modes (e.g., steady, flashing, off).
- Refer to the specific light button for front and rear lights if they operate independently.
Image 4.3: Front view of the helmet on a person, showing the integrated front LED light.
5. Operating the Helmet
Once properly fitted and adjusted, your Giro Escape MIPS helmet is ready for use. Always ensure the helmet is securely fastened before each ride. Utilize the integrated LED lights, especially during dawn, dusk, or night riding, to increase your visibility to motorists and pedestrians.
6. Maintenance
6.1. Cleaning
Regular cleaning helps maintain the helmet's condition and hygiene:
- Shell: Clean the helmet's exterior with a soft cloth, mild soap, and water. Avoid harsh chemicals or abrasive cleaners.
- Padding: The internal padding can be removed and hand-washed with mild soap and water, then air-dried. Ensure padding is completely dry before reinserting.
- Straps: Clean straps with a damp cloth and mild soap.
6.2. Battery Care for LED Lights
- Charge the integrated LED lights regularly, especially if not used for extended periods, to maintain battery health.
- Avoid fully depleting the battery frequently.
- Ensure the charging port cover is securely closed when not charging to protect against moisture and debris.
6.3. Storage
Store your helmet in a cool, dry place, away from direct sunlight and extreme temperatures. Avoid placing heavy objects on the helmet, which could deform its structure.
7. Troubleshooting
- Lights Not Turning On: Ensure the battery is charged. If fully charged and still not working, contact customer support.
- Helmet Feels Loose: Re-adjust the Roc Loc Sport MIPS dial and chin straps. Ensure the helmet is positioned correctly on your head.
- Strap Loosening: Check that the strap buckle is fully engaged and the side sliders are holding the straps firmly.
- Discomfort: Re-adjust the fit system and straps. If discomfort persists, the helmet size may be incorrect.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Giro |
| Model Name | Escape MIPS |
| Color | Matte Black |
| Age Range | Adult |
| Size | Medium (55-59 cm) |
| Special Feature | MIPS Technology, Integrated LED Lights |
| Outer Material | Acrylonitrile Butadiene Styrene (ABS) |
| Inner Material | Expanded Polystyrene (EPS) |
| Item Weight | 16 ounces (0.45 kg) |
| UPC | 768686479946 |
| Part Number | 7141438 |
| Certification | Complies with US CPSC Safety Standard for Bicycle Helmet for Persons Age 5 and Older |
9. Warranty and Support
9.1. Warranty Information
This Giro Escape MIPS helmet comes with a 2-Year Manufacturer Warranty. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accidents, modifications, or normal wear and tear. Please retain your proof of purchase for warranty claims.
9.2. Customer Support
For further assistance, technical support, or warranty inquiries, please visit the official Giro website or contact their customer service department. Contact information can typically be found on the manufacturer's website or product packaging.
