DEWENWILS HRLS11B-R1 Single Wall Mounted Switch Remote Controller Instruction Manual

Introduction

This manual provides instructions for the DEWENWILS HRLS11B-R1 Single Wall Mounted Switch Remote Controller. This device is designed to wirelessly control compatible DEWENWILS receivers (sold separately), offering convenient control over lighting or other appliances without the need for complex wiring. Please read this manual thoroughly before installation and operation.

Image: Front view of the DEWENWILS HRLS11B-R1 single wall-mounted switch remote controller, showing the 'ON' and 'OFF' buttons.

Safety Information

• This product is a remote controller and does not directly handle electrical loads. It must be paired with a compatible DEWENWILS receiver (sold separately).
• Do not attempt to open or modify the device. There are no user-serviceable parts inside.
• Keep the device away from water, moisture, and extreme temperatures.
• Ensure the battery is inserted correctly according to polarity markings.
• Dispose of used batteries responsibly according to local regulations.

Package Contents

• 1 x DEWENWILS HRLS11B-R1 Wall Mounted Switch Remote Controller
• 1 x 12V (23A) Alkaline Battery (pre-installed with insulation tab)
• 2 x Mounting Screws
• 2 x Wall Anchors

Specifications

Image: Diagram showing the dimensions of the DEWENWILS HRLS11B-R1 wall switch remote: 4.5 inches in height, 2.8 inches in width, and 0.7 inches in depth.

Setup and Installation

1. Battery Installation

1. Gently pry open the back cover of the remote controller.
2. Remove the plastic insulation tab from the battery compartment.
3. Ensure the 12V (23A) alkaline battery is correctly seated with the positive (+) and negative (-) terminals aligned as indicated.
4. Replace the back cover securely.

2. Mounting the Wall Switch Remote

The remote can be mounted to a wall using the included screws and anchors. A screwdriver (not included) is required.

1. Choose a desired location on the wall.
2. Separate the front plate from the back mounting plate of the remote.
3. Use the back mounting plate as a template to mark the positions for drilling.
4. Drill two holes, insert the wall anchors, and then secure the back mounting plate to the wall using the provided screws.
5. Snap the front plate of the remote onto the secured back mounting plate.

Image: A four-step diagram illustrating the installation process: 1. Measuring the mounting plate (1.85" x 2.91"). 2. Securing the back plate to the wall with screws. 3. Attaching the remote's front panel to the back plate. 4. The fully installed wall switch remote.

Operating Instructions

Pairing with a Receiver

This wall switch remote controller must be paired with a compatible DEWENWILS wireless receiver (e.g., plug-in outlet, light socket, in-wall module) to function. Refer to the instruction manual of your specific DEWENWILS receiver for detailed pairing steps. Generally, the process involves:

1. Plug in or power on your DEWENWILS receiver.
2. Within a few seconds of powering on the receiver, press and hold the "ON" or "OFF" button on this wall switch remote for approximately 3-5 seconds until the receiver indicates successful pairing (e.g., a light flashes or the connected device turns on/off).
3. Test the remote by pressing the "ON" and "OFF" buttons to ensure proper control of the receiver.

Note: This remote is designed to be programmable and expandable, allowing it to control multiple receivers or be controlled by multiple remotes. Consult your receiver's manual for advanced pairing options.

Image: A diagram illustrating various DEWENWILS remote control products, including different types of receivers (plug-in, light socket, in-wall) and remote controllers, demonstrating how they can be freely paired to create custom lighting combinations.

Basic Operation

• Press the ON button to turn on the paired receiver and its connected device.
• Press the OFF button to turn off the paired receiver and its connected device.

Image: A composite image showing the DEWENWILS wall switch remote in use, highlighting features like "No Wiring Needed," "100 Ft Long Range," "Programmable and Expandable," and "Handheld Remote Available." It also displays ETL Listed and FCC certifications.

Maintenance

• Clean the remote controller with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Replace the 12V (23A) battery when the remote's range decreases or it becomes unresponsive. To replace, follow the battery installation steps in the Setup section.
• Store the remote in a dry environment when not in use for extended periods.

Troubleshooting

Warranty and Support

DEWENWILS products are designed for reliability and performance. For warranty information, technical support, or customer service inquiries, please refer to the documentation included with your DEWENWILS receiver or visit the official DEWENWILS website.

Website: www.dewenwils.com