Introduction
This manual provides essential information for the assembly, operation, maintenance, and troubleshooting of your Keter Claire 2 Seater Sofa Set with Storage Table. Please read these instructions carefully before assembly and use to ensure safe and optimal performance of your product.
The Keter Claire Sofa Set is designed for both indoor and outdoor use, offering a comfortable seating solution with integrated storage. It is constructed from durable molded plastic, resistant to UV rays and various weather conditions.
Product Components:
- 1 x Two-seater Sofa
- 2 x Armchairs
- 1 x Storage Table
- Cushions (for sofa and armchairs)
Important Safety Information
Please observe the following safety precautions to prevent injury or damage to the product:
- Do not stand or jump on the furniture.
- Ensure all components are securely fastened before use.
- Keep away from open flames or extreme heat sources.
- Do not overload the storage table.
- Supervise children when they are near or using the furniture.
Setup and Assembly
The Keter Claire Sofa Set requires assembly. It is recommended that two adults perform the assembly. No special tools are typically required, as components are designed for interlocking or simple screw fastening.
Before You Begin:
- Unpack all components and verify against the parts list.
- Ensure you have sufficient space for assembly.
- Keep small parts away from children.
Assembly Steps:
- Step 1: Assemble the Armchairs. Connect the backrest to the seat base, then attach the armrests. Ensure all clips or screws are firmly engaged.
- Step 2: Assemble the Two-seater Sofa. Similar to the armchairs, connect the backrest to the seat base, then attach the armrests.
- Step 3: Assemble the Storage Table. Connect the side panels to the base and top. Ensure the lid mechanism (if any) is correctly installed.
- Step 4: Place Cushions. Once all furniture pieces are assembled, place the provided cushions onto the seats for comfort.
Figure 1: Fully assembled Keter Claire 2 Seater Sofa Set. This image displays the complete set, including the two armchairs, the two-seater sofa, and the central storage table, all in a graphite grey finish with light grey seat cushions.
Operating Instructions
The Keter Claire Sofa Set is designed for comfortable seating and convenient storage.
Using the Seating:
- Ensure the furniture is placed on a flat, stable surface.
- The cushions are designed for outdoor use but it is recommended to store them indoors during prolonged periods of rain or harsh weather to maintain their condition.
Using the Storage Table:
The central table features integrated storage, ideal for keeping small outdoor items, cushions (when not in use), or other accessories.
- To access storage, lift the tabletop.
- Do not store heavy or sharp objects that could damage the interior.
- Ensure the lid is properly closed to protect contents from elements.
Figure 2: Detail of the Keter Claire Storage Table. This image highlights the textured surface and the design of the storage table, which is part of the sofa set. A small green teapot is visible on its surface.
Maintenance and Care
The Keter Claire Sofa Set is designed for low maintenance and high durability. Following these simple care instructions will help prolong its lifespan and appearance:
Cleaning:
- Wipe down the plastic surfaces with a damp cloth and mild soap solution.
- Rinse thoroughly with clean water to remove any soap residue.
- Avoid using abrasive cleaners, harsh chemicals, or stiff brushes, as these can damage the surface.
- For cushions, spot clean with a mild detergent and water. Allow to air dry completely before storing.
Storage:
- While the set is weather-resistant, storing it indoors or covering it with a protective cover during extreme weather conditions (heavy snow, prolonged rain, strong winds) will extend its life.
- Store cushions in a dry, protected area when not in use, especially during off-season.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Difficulty assembling parts | Parts not aligned correctly; excess plastic from molding. | Ensure parts are correctly oriented as per instructions. Gently tap into place. If excess plastic, carefully trim with a utility knife (with caution). |
| Furniture feels wobbly after assembly | Components not fully engaged or secured. | Check all connection points to ensure they are fully clicked into place or screws are tightened. Ensure furniture is on a level surface. |
| Cushions getting wet/damp | Left exposed to rain or high humidity. | Store cushions in the storage table or indoors during wet weather. Allow to air dry completely if they get wet. |
Specifications
| Attribute | Detail |
|---|---|
| Brand | Keter |
| Model Number | K253084 |
| Material | Molded Plastic |
| Colour | Graphite/Gray |
| Storage Table Dimensions (L x W x H) | 60 x 120 x 64 cm |
| Overall Set Weight | 36 kg |
| Assembly Required | Yes |
| Resistance | UV rays and weather effects |
| Usage | Indoor and Outdoor |
Warranty and Support
For information regarding warranty coverage, product support, or to purchase replacement parts, please contact Keter customer service or visit the official Keter website. Please have your model number (K253084) and proof of purchase available when contacting support.
Note: Warranty terms may vary by region and retailer. Refer to your purchase documentation for specific details.
