Introduction
This manual provides comprehensive instructions for the safe and effective installation, operation, and maintenance of your JESLED 32.8ft (10m) 3000K Warm White 24V LED Strip Light. Please read this manual thoroughly before use and retain it for future reference.
Product Overview
Package Contents
Verify that all items listed below are included in your package:
- 2 x 16.4ft (5m) Warm White LED Strip Lights
- 1 x DC 24V Power Adapter with Dimmer
- 1 x Splitter Cable
- 4 x 10mm Gapless Solderless Connectors
- 12 x 10mm Fixing Clips
- 12 x Screws
Image: The complete JESLED LED strip light kit, including two rolls of warm white LED strips, a power adapter, a splitter cable, gapless connectors, mounting clips, and screws.
Key Features
- Flexible Design: The LED strip is highly flexible, allowing for easy contouring around corners and irregular surfaces.
- Dimmable Lighting: Features 10 adjustable brightness levels for customized illumination.
- Warm White (3000K): Provides a comfortable and inviting light color suitable for various indoor settings.
- High Brightness: Utilizes 600 high-quality 2835 LEDs for significant light output.
- Safe 24V Operation: Designed for low voltage 24V operation, enhancing safety.
- Long Lifespan: Offers an extended operational life of over 50,000 hours.
- Easy Installation: Equipped with strong 3M adhesive backing for simple peel-and-stick application.
- Cuttable Design: Can be cut every 5 LEDs at designated marks to achieve desired lengths.
Image: A hand holding an illuminated LED strip, emphasizing its safe-to-touch and flexible nature, with icons representing 3000K color, 3M adhesive, dimming capability, and easy installation.
Safety Information
- Power Supply: Only use the provided 24V DC power adapter. Using an incompatible power supply may damage the product or pose a safety risk.
- Indoor Use Only: This product is designed for indoor applications. Do not expose to water or outdoor elements.
- Ventilation: Ensure adequate ventilation around the LED strips, especially when operating for extended periods. Do not operate the LED strip while it is still rolled on the spool.
- Cutting: Only cut the LED strip at the designated cutting marks. Cutting elsewhere will damage the circuit and render that section unusable.
- Installation Surface: Install on clean, dry, and smooth surfaces to ensure proper adhesion and heat dissipation.
- Children and Pets: Keep the product and its components out of reach of children and pets.
Image: Visual warning against operating the LED strip while still rolled up, showing a rolled strip with a red 'X' and an unrolled strip with a green checkmark, indicating proper usage for heat dissipation.
Setup and Installation
Before Installation
- Unpack: Carefully remove all components from the packaging.
- Test: Before permanent installation, connect the LED strip to the power adapter and plug it into an outlet to ensure it functions correctly.
- Plan: Determine the desired path for your LED strip. Measure and plan any necessary cuts or connections.
Installation Steps
- Prepare the Surface: Ensure the installation surface is clean, dry, and smooth. Wipe away any dust, grease, or moisture. A clean surface is crucial for optimal adhesive performance.
Image: Illustrating the first step of installation: wiping the surface clean before applying the LED strip.
- Peel and Stick: Carefully peel off the protective backing from the 3M adhesive tape on the back of the LED strip. Press the strip firmly onto the prepared surface along your desired path. Apply even pressure to ensure good contact.
Image: Showing the second step of installation: peeling off the adhesive backing and attaching the LED strip to the prepared surface.
- Secure with Clips (Optional but Recommended): For added security, especially on textured surfaces or in areas with potential movement, use the provided fixing clips and screws. Space the clips evenly along the strip.
- Connect Power: Connect the LED strip(s) to the splitter cable (if using two strips), then connect the splitter cable to the DC 24V power adapter. Plug the power adapter into a standard electrical outlet.
Cutting and Connecting
The LED strip can be cut to your desired length. Look for the designated cutting marks, typically indicated by a copper pad and a scissor icon, located every 5 LEDs. Use sharp scissors to cut precisely along these marks.
Image: Close-up view of the LED strip showing designated cut points marked every 5 LEDs and the protective backing being peeled from the 3M adhesive tape.
To reconnect cut sections or extend the strip, use the provided gapless solderless connectors. Ensure the polarity (+ and -) on the strip aligns with the connector.
Operation
Powering On/Off
Press the power button on the DC 24V power adapter to turn the lights on. Press and hold the power button for approximately two seconds to turn the lights off.
Brightness Adjustment
The power adapter includes buttons for brightness control. Press the '+' button to increase brightness and the '-' button to decrease brightness. There are 10 distinct brightness levels available.
Image: Demonstrating the brightness adjustment feature, showing a living room with varying light levels and a close-up of the power adapter with 'increase' and 'reduce' brightness buttons.
Maintenance
- Cleaning: To clean the LED strip, ensure it is unplugged from the power source. Gently wipe the strip with a soft, dry, or slightly damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Adhesive: If the adhesive begins to lose its grip over time, consider using the provided mounting clips or additional adhesive solutions to secure the strip.
- Inspection: Periodically inspect the strip and connections for any signs of damage or wear.
Troubleshooting
- Lights Not Turning On:
- Ensure the power adapter is securely plugged into a working electrical outlet.
- Check all connections between the LED strip, splitter, and power adapter to ensure they are firm and correctly aligned (positive to positive, negative to negative).
- Verify that the power button on the adapter has been pressed.
- Lights Flickering or Uneven Brightness:
- Check for loose connections.
- Ensure the power adapter is not overloaded. If using multiple strips, confirm the total wattage does not exceed the adapter's capacity.
- Avoid sharp bends or kinks in the LED strip that could damage internal wiring.
- Adhesive Not Sticking:
- Ensure the installation surface was clean, dry, and smooth before application.
- Apply firm pressure along the entire length of the strip during installation.
- Use the provided mounting clips for additional support, especially on challenging surfaces.
- Overheating:
- Never operate the LED strip while it is rolled up on the spool, as this can cause excessive heat buildup.
- Ensure the strip is installed in an area with adequate airflow.
- Only use the power adapter supplied with the product. Using a different adapter may lead to overheating or damage.
Specifications
| Model Number | JW-NWP2835-24V-WW-2P |
| Brand | JESLED |
| Light Color | Warm White |
| Color Temperature | 3000 Kelvin |
| LED Type | 2835 LEDs |
| Number of LEDs | 600 (per 32.8ft/10m strip) |
| Voltage | 24 Volts DC |
| Wattage | 60 Watts |
| Special Feature | Dimmable (10 levels) |
| Control Method | Remote Control (via adapter buttons) |
| Lifespan | 50,000+ Hours |
| Indoor/Outdoor Usage | Indoor Only |
| Material | Metal, Vinyl |
| Item Weight | 1.06 pounds |
| Package Dimensions | 5.47 x 5.43 x 2.56 inches |
Warranty and Support
JESLED products are manufactured to high-quality standards. For specific warranty information, please refer to the product packaging or contact JESLED customer support directly. If you encounter any issues or have questions regarding your LED strip light, please reach out to the retailer or manufacturer for assistance.
For further assistance, please visit the JESLED Store on Amazon.
