1. Introduction
Thank you for choosing the PRIMO Deluxe Hot and Cold Bottled Water Dispenser, Model 676065. This appliance provides convenient access to both refreshing cold water and piping hot water for beverages and instant meals. Its compact design makes it suitable for various environments, including homes and small offices. Please read this manual thoroughly before installation and operation to ensure safe and efficient use.
2. Important Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury, always follow basic safety precautions.
- Read all instructions before using the appliance.
- This appliance must be properly grounded. Connect only to properly grounded outlets.
- Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
- Do not immerse the dispenser, cord, or plug in water or other liquids.
- Close supervision is necessary when any appliance is used by or near children.
- Do not use outdoors.
- Do not use with water that is microbiologically unsafe or of unknown quality.
- Always unplug the dispenser before cleaning or servicing.
- Exercise caution when dispensing hot water. The hot water tap features a child-resistant safety mechanism.
- Ensure adequate ventilation around the dispenser. Maintain at least 10 cm (4 inches) clearance from walls.
3. Setup and Installation
3.1 Unpacking
- Carefully remove the dispenser from its packaging.
- Inspect for any shipping damage. If damaged, do not operate and contact customer support.
- Remove all packaging materials, including any protective films or tapes.
3.2 Placement
- Place the dispenser on a flat, level, and sturdy surface capable of supporting its weight when full.
- Ensure the dispenser is placed indoors, away from direct sunlight and heat sources.
- Allow at least 10 cm (4 inches) of clearance from the back and sides of the dispenser to a wall for proper ventilation.
- This dispenser does not require plumbing and operates as a standalone unit.
Image: Front view of the PRIMO Deluxe Hot and Cold Bottled Water Dispenser with a water bottle on top, a red mug under the hot water tap, and a glass under the cold water tap.
3.3 Water Bottle Installation
- This dispenser is compatible with 10L, 11L, 15L, and 18L water bottles.
- Clean the neck of the water bottle before placing it on the dispenser.
- Remove the cap from the water bottle.
- Carefully lift the water bottle and place it upright onto the bottle support collar on top of the dispenser. Ensure it is seated firmly.
Image: Close-up of the dispenser's side, highlighting its universal fitting for 10L, 11L, 15L, and 18L water bottles, its suitability for home and small offices, and lever faucet controls.
3.4 Initial Flushing and Power Connection
- Once the water bottle is installed, allow approximately 5 minutes for the tanks to fill.
- Place a large container under the cold water tap and dispense water until it flows steadily. Repeat for the hot water tap (if applicable, ensure power is off for this initial flush).
- Plug the power cord into a grounded electrical outlet.
- Turn on the hot and cold water switches located on the back of the dispenser. The indicator lights on the front will illuminate.
4. Operating Instructions
4.1 Dispensing Cold Water
- Place a glass or cup under the blue (cold water) tap.
- Press the blue lever faucet control to dispense cold water.
- Release the lever to stop the flow.
Image: A person's hand dispensing cold water into a glass from the dispenser.
4.2 Dispensing Hot Water
- Place a heat-resistant cup or mug under the red (hot water) tap.
- This dispenser features a child-resistant safety hot water tap. To dispense hot water, simultaneously press the red safety button and the red lever faucet control.
- Release both the button and the lever to stop the flow.
- Allow approximately 15-20 minutes for the hot water to reach its optimal temperature after turning on the hot water switch.
Image: A person's hand dispensing hot water into a white mug from the dispenser, pressing the red safety button.
5. Maintenance
Regular maintenance ensures optimal performance and hygiene of your water dispenser.
5.1 Cleaning the Drip Tray
- The drip tray is removable and dishwasher-safe for easy cleaning.
- Periodically remove the drip tray and empty any collected water.
- Wash the drip tray with mild soap and water, or place it in the dishwasher.
- Rinse thoroughly and dry before reinserting.
Image: Close-up of the dispenser's front panel, highlighting quiet cooling and heating (≤48dB), child-resistant safety hot water tap, and removable dishwasher-safe drip tray.
5.2 Exterior Cleaning
- Unplug the dispenser before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth.
- Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
- The base is made of stainless steel and can be cleaned with a stainless steel cleaner if desired.
5.3 Descaling (Recommended Annually)
- Unplug the dispenser and remove the water bottle.
- Drain all water from both hot and cold tanks using the drain plugs (usually located at the back).
- Prepare a descaling solution (e.g., a mixture of white vinegar and water, or a commercial descaling agent designed for water dispensers).
- Pour the solution into the dispenser's reservoir.
- Allow the solution to sit for 30 minutes to 1 hour.
- Drain the solution completely.
- Rinse the dispenser thoroughly by filling it with clean water and draining it several times to remove any residual descaling solution.
- Replace drain plugs, install a new water bottle, and plug in the dispenser.
6. Troubleshooting
Before contacting customer support, please refer to the following table for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No cold water | Cold water switch off; Dispenser unplugged; Empty water bottle; Cooling system malfunction. | Ensure cold water switch is ON; Check power connection; Replace water bottle; Contact customer support. |
| No hot water | Hot water switch off; Dispenser unplugged; Empty water bottle; Heating system malfunction. | Ensure hot water switch is ON; Check power connection; Replace water bottle; Contact customer support. |
| Water leaking | Water bottle cracked or improperly seated; Drain plug loose; Internal leak. | Check water bottle for cracks and reseat it properly; Tighten drain plug; Unplug and contact customer support. |
| Water has unusual taste/odor | Old water bottle; Dispenser needs cleaning/descaling. | Replace water bottle; Perform a thorough cleaning and descaling of the dispenser. |
| Dispenser is noisy | Normal operation (compressor/heating); Dispenser not level. | Some noise is normal (≤48dB); Ensure dispenser is on a level surface. |
7. Specifications
Below are the technical specifications for the PRIMO Deluxe Hot and Cold Bottled Water Dispenser, Model 676065.
| Feature | Detail |
|---|---|
| Brand | PRIMO |
| Model Number | 676065 |
| Color | Black |
| Material | Stainless Steel (Base) |
| Dimensions (L x W x H) | 30.8 x 28.4 x 93.8 cm (12.1 x 11.2 x 36.9 inches) |
| Item Weight | 13.18 kg (29.06 lbs) |
| Cold Tank Capacity | 3 Liters (usable volume 2.7 Liters) |
| Hot Tank Capacity | 1.02 Liters |
| Chilled Temperature Range | 4°C to 10°C (39.2°F to 50°F) |
| Hot Temperature Range | 87°C to 92°C (188.5°F to 197.6°F) |
| Noise Level | ≤48 dB (Quiet Cooling & Heating) |
| Installation Type | Freestanding |
| Water Access Location | Top-loading |
| Faucet Controls | Lever Faucets |
| Power Source | Electric Cord |
| Special Features | Child-resistant hot water tap, Removable dishwasher-safe drip tray, No plumbing required, Universal bottle fitting. |
Image: Diagram illustrating the dimensions (97cm height, 33cm width, 33cm depth) and capacities (3L cold tank, 1.02L hot tank) of the dispenser.
Image: Close-up of the dispenser's front panel, highlighting the hot temperature range (188.5°F to 197.6°F), chilled temperature range (39.2°F to 50°F), no plumbing requirement, and stainless steel base.
8. Warranty and Support
For warranty information, please refer to the documentation included with your product at the time of purchase. If you require technical assistance, have questions about your product, or need to report a malfunction, please contact PRIMO customer support. You can typically find contact details on the manufacturer's official website or on the product packaging.
Please have your model number (676065) and proof of purchase ready when contacting support.
