Introduction
Thank you for choosing the Primo Deluxe Water Dispenser. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your new water dispenser. Please read it thoroughly before use and retain it for future reference.
Image: Front view of the Primo Deluxe Water Dispenser, showcasing its sleek design with a water bottle installed on top, ready for use.
Important Safety Information
To reduce the risk of injury and property damage, please read all instructions and warnings before assembling, installing, and operating this water dispenser.
- Always place the dispenser on a level, stable surface.
- Ensure the dispenser is plugged into a grounded electrical outlet.
- Keep the dispenser away from direct sunlight and heat sources.
- Do not operate the dispenser with a damaged cord or plug.
- Unplug the dispenser before cleaning or performing any maintenance.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Setup
- Unpacking: Carefully remove the dispenser from its packaging. Inspect for any damage.
- Placement: Position the dispenser on a flat, sturdy surface. Ensure there is at least 10 cm (4 inches) of clearance from the wall for proper ventilation. The dispenser requires only one electrical outlet.
- Bottle Installation: Remove the protective seal from a new 10L, 11L, 15L, or 18L water bottle. Invert the bottle and place it securely onto the piercing probe on top of the dispenser.
- Initial Flush: Before connecting to power, dispense at least 1 liter of water from each faucet to ensure the tanks are filled and to flush any air from the system.
- Power Connection: Plug the dispenser into a grounded 220-240V AC electrical outlet. Allow approximately 1 hour for the water to reach its optimal chilled temperature.
Image: Rear view of the water dispenser, illustrating the power cord and cooling components, emphasizing the need for proper ventilation.
Operating Instructions
The Primo Deluxe Water Dispenser provides chilled water with simple lever faucet controls.
- Dispensing Chilled Water: Place your glass or reusable container under the blue-marked faucet. Press the drinking vessel against the lever to dispense chilled water. Release the lever to stop the flow. The chilled water temperature ranges from 4°C to 10°C.
- Dispensing Room Temperature Water: Place your glass or reusable container under the red-marked faucet. Press the drinking vessel against the lever to dispense room temperature water. Release the lever to stop the flow.
Image: A hand holding a glass, pressing it against the dispenser's lever to activate water flow, demonstrating the hands-free dispensing mechanism.
Image: Detailed view of the lever faucet controls, highlighting their design for quick and easy dispensing.
Maintenance
Regular cleaning ensures optimal performance and hygiene of your water dispenser.
- Exterior Cleaning: Wipe the exterior surfaces of the dispenser with a soft, antibacterial cloth. Avoid abrasive cleaners or solvents.
- Drip Tray Cleaning: The drip tray is removable and dishwasher-safe. Empty and clean it regularly to prevent overflow and bacterial growth.
- Internal Cleaning: For thorough internal cleaning, consult the Primo website or customer support for recommended cleaning kits and procedures.
Image: A close-up emphasizing the easy-to-clean features, including the removable and dishwasher-safe drip tray.
Troubleshooting
If you encounter issues with your dispenser, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No water dispensing | Empty water bottle; airlock in system; dispenser unplugged. | Replace water bottle; dispense water from both faucets to clear airlock; ensure dispenser is plugged in. |
| Water not cold enough | Dispenser recently plugged in; poor ventilation; cooling system malfunction. | Allow 1 hour for cooling; ensure adequate space around dispenser; contact customer support if problem persists. |
| Water leaking | Improperly seated water bottle; cracked water bottle; damaged internal component. | Re-seat bottle; replace bottle; unplug and contact customer support. |
Specifications
- Brand: Primo
- Model: 676066
- Color: Black and Silver
- Dimensions (H x W x D): Approximately 97 cm x 33 cm x 33 cm (38.2 in x 13 in x 13 in)
- Weight: 12.4 kg (27.3 lbs)
- Cold Water Tank Capacity: 3 Liters (usable volume 2.7 Liters)
- Chilled Water Temperature Range: 4°C to 10°C (39.2°F to 50°F)
- Noise Level: ≤ 48 dB (Quiet Cooling)
- Dispensing Height: 22.5 cm (8.8 inches)
- Installation Type: Freestanding, Top-loading
- Compatible Bottle Sizes: 10L, 11L, 15L, 18L
- Power Requirement: Standard electrical outlet (no plumbing required)
Image: A visual representation of the dispenser's dimensions (height, width, depth) and weight, along with cold water tank capacity.
Image: Highlights key features such as its modern design, chilled temperature range, lack of plumbing requirement, and durable stainless steel base.
Warranty and Support
Primo products are manufactured to high-quality standards. For warranty information, please refer to the documentation included with your purchase or visit the official Primo website. If you require technical assistance or have questions not covered in this manual, please contact Primo Customer Support.
Primo Customer Support:
- Website: www.primowater.com
- Phone: Refer to your regional Primo website for local contact numbers.
