Product Overview
The CAT CJ1000DXT Jump Starter and Power Station is a versatile device designed for automotive and portable power needs. It integrates a powerful jump starter, an air compressor, a power inverter, and USB charging ports into a single unit, providing comprehensive utility for various situations.
Front view of the CAT CJ1000DXT Jump Starter and Powerstation, showing the control panel, LED light, USB ports, and AC outlet.
Rear view of the CAT CJ1000DXT, displaying the integrated jumper cables and storage compartments.
Important Safety Information
Always read and understand the complete instruction manual before operating this device. Failure to follow safety guidelines can result in serious injury or property damage.
- Ensure adequate ventilation when operating, especially during charging or jump-starting.
- Avoid sparks or flames near the battery to prevent explosions from battery gases.
- Wear eye protection and gloves when handling batteries.
- The unit features a reverse polarity alarm to alert you if clamps are connected incorrectly. Always ensure correct polarity (red to positive, black to negative) before attempting to jump start.
- Keep out of reach of children.
Excerpt from the Quick Start Guide, highlighting important safety warnings and operational icons.
Setup and Initial Charging
Before first use, fully charge the unit for 40 hours. Regular recharging is essential for optimal performance and battery life. It is recommended to recharge the unit every 30 days, or after each use, to maintain the internal battery.
- Locate the AC charging port on the unit.
- Connect the provided AC charging cable to the unit and then to a standard 120V AC wall outlet.
- Allow the unit to charge until the battery level indicator shows full.
Operating Instructions
Jump Starting a Vehicle
The 1200 Peak Amp Jump Starter is designed to start most 12V vehicles, including large V8-powered cars and trucks, without the need for another vehicle.
- Ensure the jump starter is fully charged.
- Connect the red positive (+) clamp to the positive terminal of the vehicle's battery.
- Connect the black negative (-) clamp to a clean, unpainted metal part of the vehicle's chassis, away from the battery and fuel lines.
- Turn the jump starter's main switch to the "ON" position.
- Attempt to start the vehicle. If it doesn't start immediately, wait a few minutes before trying again.
- Once the vehicle starts, immediately disconnect the black negative (-) clamp first, then the red positive (+) clamp.
Using the Air Compressor
The 120 PSI AutoStop Compressor is ideal for inflating tires and sports equipment. The digital display allows for precise pressure setting.
- Connect the air hose to the tire valve or inflation accessory.
- Use the up/down arrows on the control panel to set the desired PSI.
- Press the "AIR" button to begin inflation. The compressor will automatically stop once the preset pressure is reached.
- Disconnect the air hose.
Official product overview video demonstrating the features of the CAT CJ1000DXT, including the air compressor functionality.
Power Inverter and USB Charging
The unit features a 200-watt portable power inverter with a 120V AC outlet and multiple 5V USB ports (6.2A total) for charging personal electronics.
- To use the AC outlet, plug your device into the 120V AC outlet and press the "AC POWER" button.
- To use the USB ports, plug your USB device into any of the 5V USB ports. The USB power is always on when the unit is powered on.
High-Intensity LED Worklight
The integrated LED worklight provides illumination for various tasks, especially in low-light conditions.
- Press the "LED" button on the control panel to turn the worklight on or off.
Maintenance
Proper maintenance ensures the longevity and reliability of your CAT Power Station.
- Recharging: Recharge the unit every 30 days or immediately after each use to maintain battery health.
- Cleaning: Wipe the exterior with a damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures. Ensure all cables are neatly stored in their designated compartments.
Troubleshooting
If you encounter issues with your CAT CJ1000DXT, refer to the following common solutions. For more detailed troubleshooting, consult the full instruction manual.
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not turn on. | Battery is fully discharged. | Charge the unit for 40 hours. |
| Vehicle does not jump start. | Incorrect clamp connection (reverse polarity). | Ensure red clamp is on positive (+) and black clamp on negative (-) or chassis. The reverse polarity alarm will sound if incorrect. |
| Air compressor not inflating. | Hose not securely connected or desired PSI not set. | Check hose connection and ensure PSI is set on the digital display. |
Specifications
- Brand: CAT
- Model: CJ1000DXT
- Jump Start Amperage: 1200 Peak Amps
- Power Inverter: 200 Watt (120V AC outlet)
- USB Ports: 5V, 6.2A total (multiple ports)
- Air Compressor: 120 PSI AutoStop
- Weight: Approximately 18.96 pounds
- Dimensions: Approximately 14 x 11 x 9.5 inches
- Charging Time: 40 Hours (initial charge)
Warranty and Support
For specific warranty details, please refer to the warranty booklet included with your product. CAT products are generally known for their durability and quality.
For technical support or assistance, please contact:
Technical Support Phone Number: 855-806-9228
You may also visit the official CAT website for additional resources and support information.
