Innosilicon T3+ BTC SHA-256 ASIC Miner 57TH User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your Innosilicon T3+ BTC SHA-256 ASIC Miner 57TH. Please read this manual thoroughly before setting up and operating the device to ensure optimal performance and longevity.

An image showing the Innosilicon T3+ ASIC Miner, a rectangular white unit with cooling fans visible on one side and power connections on the other.

2. Safety Information

Observe the following safety precautions to prevent injury or damage to the device:

• Ensure proper grounding for all electrical connections.
• Do not operate the miner in environments with high humidity or extreme temperatures outside the specified range (0-40°C).
• Maintain adequate ventilation around the device to prevent overheating.
• Do not block the air inlets or outlets.
• Disconnect power before performing any maintenance or cleaning.
• Only use the provided power supply unit (PSU) or a compatible, certified replacement.
• Keep out of reach of children.

3. Package Contents

Verify that all components are present in the package:

• Innosilicon T3+ BTC SHA-256 ASIC Miner 57TH
• Integrated Power Supply Unit (PSU)
• Power Cable (region-specific)
• Ethernet Cable (optional, may not be included)

4. Setup

4.1 Environmental Considerations

The T3+ miner requires a stable and controlled environment for optimal performance and longevity. Ensure the operating temperature is between 0-40°C and the humidity is low. A dedicated mining farm with proper cooling and a dust filter environment is highly recommended to prevent dust accumulation and maintain efficient operation.

4.2 Physical Placement

Place the miner on a stable, flat surface. Ensure there is sufficient space around the device for proper airflow, especially around the cooling fans. Do not place the miner near heat sources or in enclosed spaces.

4.3 Electrical Connection

1. Connect the power cable to the integrated PSU on the miner.
2. Plug the other end of the power cable into a grounded electrical outlet. The miner operates at approximately 3300W (+/- 10%) and requires a stable power source with a maximum input voltage of 240 Volts. Ensure your electrical infrastructure can support this load.

4.4 Network Connection

1. Connect one end of an Ethernet cable to the Ethernet port on the miner.
2. Connect the other end of the Ethernet cable to your network router or switch.
3. Ensure your network provides a stable internet connection for mining operations.

5. Operating Instructions

5.1 Initial Power-On

Once all connections are secure, power on the miner. The fans will start, and the device will begin its boot sequence. This may take a few minutes.

5.2 Configuration

The Innosilicon T3+ typically uses a web-based interface for configuration. To access it:

1. Determine the IP address of your miner. This can often be found through your router's connected devices list or by using an IP scanner tool on your network.
2. Open a web browser on a computer connected to the same network and enter the miner's IP address in the address bar.
3. Log in using the default credentials (refer to the manufacturer's documentation or common default credentials for Innosilicon devices).
4. Configure your mining pool settings (URL, Worker, Password) within the web interface. The T3+ is designed for SHA-256 algorithm mining.
5. Save the settings and restart the miner if prompted.

5.3 Monitoring Performance

Regularly monitor the miner's performance through its web interface. Key metrics to observe include:

• Hashrate: Aim for the specified 57TH/s (+/-6%). Fluctuations may indicate issues.
• Temperature: Ensure the operating temperature remains within safe limits to prevent damage to the ASIC chips.
• Fan Speed: Verify fans are operating correctly and at appropriate speeds.
• Uptime: Monitor continuous operation.

6. Maintenance

Regular maintenance ensures the longevity and efficiency of your T3+ miner:

• Dust Removal: Periodically clean the miner, especially the fans and heatsinks, to prevent dust buildup. Dust can impede airflow and lead to overheating. Use compressed air or a soft brush. Ensure the device is powered off and unplugged before cleaning.
• Environmental Check: Continuously monitor the ambient temperature and humidity of the operating environment. Adjust cooling solutions as needed to maintain optimal conditions.
• Cable Inspection: Regularly inspect all power and network cables for any signs of wear or damage. Replace damaged cables immediately.

7. Troubleshooting

This section addresses common issues you might encounter:

If you encounter issues not listed here or if solutions do not resolve the problem, please contact Innosilicon customer support.

8. Specifications

9. Warranty Information

For detailed warranty terms and conditions, please refer to the official Innosilicon website or the warranty card included with your purchase. Typically, warranty coverage addresses manufacturing defects. Any unauthorized modifications, improper installation, or operation outside of specified environmental conditions may void the warranty.

10. Customer Support

If you require technical assistance, have questions about your miner, or need to report an issue, please contact Innosilicon customer support through their official channels. Have your product model (T3+) and serial number ready when contacting support for faster service.

You can typically find support contact information on the official Innosilicon website: www.innosilicon.com