Monstake Automatic Foam Soap Dispenser User Manual

Introduction

Welcome to your new Monstake Automatic Foam Soap Dispenser. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before first use and keep it for future reference.

Image: The Monstake Automatic Foam Soap Dispenser, showcasing its sleek black design and touchless foam dispensing.

Important Safety Information

To ensure safe operation and prevent damage, please observe the following:

• Read all instructions carefully before using the dispenser.
• Do not immerse the device in water or other liquids. This product is not fully waterproof.
• Keep the dispenser out of reach of small children to prevent accidental ingestion of soap or damage to the device.
• Use only recommended soap types. Gel soap must be diluted before use to ensure proper foaming and prevent clogging.
• Do not attempt to disassemble or repair the device yourself. Contact customer support for assistance.

Package Contents

Verify that all items are included in your package:

• 1 x Monstake Automatic Foam Soap Dispenser
• 1 x User Manual
• 1 x USB Charging Cable
• 1 x Strong Non-marking Adhesive
• 2 x Mounting Screws
• 2 x Safety Screws

Image: A visual representation of all items included in the Monstake Automatic Foam Soap Dispenser package.

Product Overview

Familiarize yourself with the main components of your Monstake Automatic Foam Soap Dispenser:

• Dispenser Body: The main unit housing the reservoir and electronics.
• Nozzle: Where the foam is dispensed.
• Smart Display: An LCD screen showing time, dispensing gear, and battery level.
• Touch Button: Used for power control and settings adjustment.
• Charging Port: Located on the side for USB charging.
• Refill Opening: Top opening for adding soap solution.

Image: The smart display of the dispenser, clearly showing the current gear setting, time, and battery status indicators.

Setup

1. Charging the Dispenser

Before first use, fully charge the dispenser. Connect the provided USB charging cable to the dispenser's charging port and a suitable USB power source (e.g., wall adapter, computer USB port). A full charge typically takes 2-3 hours and can provide power for up to 4 months of use.

Image: The dispenser being charged via its USB port, highlighting the long battery life.

2. Filling the Dispenser

The dispenser has a capacity of 6.76 oz (200 ml).

• For Foam Soap: Pour foam soap directly into the reservoir. No dilution is needed.
• For Gel Soap (e.g., shampoo, shower gel, handwash, dishwash): Gel soap must be diluted with water before use to create foam. The recommended dilution ratio is 10%-30% gel soap to 30%-70% water. Mix thoroughly before pouring into the reservoir.

Image: Instructions for diluting gel soap and examples of the dispenser's application in kitchen and bathroom environments.

3. Installation

The Monstake dispenser is designed for wall-mounted installation. To prevent accidental dispensing, it is recommended to install the dispenser at least 0.65 ft (20 cm) above the countertop or sink.

There are two installation methods:

• Non-marking Adhesive Sticker: Suitable for smooth, non-porous surfaces. Clean and dry the wall surface thoroughly before applying the adhesive.
• Screws: Recommended for cement walls or surfaces where a more secure, permanent installation is desired. Use the provided mounting screws and safety screws.

Image: Detailed instructions for both drill-free adhesive installation and screw-based installation, including recommended mounting height.

Operating Instructions

Power On/Off

Locate the touch button on the side of the dispenser. Press and hold the button for a few seconds to power the device on or off. The smart display will illuminate when the device is powered on.

Adjusting Foam Gears

The dispenser offers 3 adjustable foam gears to control the amount of soap dispensed. Briefly press the touch button to cycle through the gears (1, 2, 3). The current gear setting will be displayed on the LCD screen. The dispensing speed is approximately 0.25 seconds.

Image: Visual comparison of the foam volume dispensed at each of the three adjustable gear settings.

Using the Smart Display

The LCD screen provides real-time information:

• Clock: Displays the current time.
• Gear Position: Indicates the selected dispensing gear (1, 2, or 3).
• Battery Level: Shows the remaining battery charge.

Maintenance

Cleaning

To clean the exterior of the dispenser, wipe it gently with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish. Ensure no water enters the charging port or other openings.

Refilling

When the soap level is low, refill the dispenser by opening the top cap and pouring in the appropriate soap solution as described in the "Filling the Dispenser" section under Setup. Ensure the cap is securely closed after refilling.

Battery Care

Recharge the dispenser when the battery level indicator on the smart display shows low charge. Avoid completely draining the battery for extended periods to prolong its lifespan. Use only the provided USB charging cable.

Troubleshooting

If you encounter issues with your Monstake Automatic Foam Soap Dispenser, please refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact Monstake customer support for further assistance.

Specifications

Warranty and Support

Your Monstake Automatic Foam Soap Dispenser comes with a one-year warranty service from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.

For warranty claims, technical support, or any questions regarding your product, please contact the Monstake after-sales team through Amazon's messaging system or refer to the contact information provided on the after-sales card included in your package.

You can also visit the official Monstake Store on Amazon for more information and products: Monstake Store