EVERYBOT Three-Spin Robot Mop TS300 Instruction Manual

1. Introduction

Thank you for choosing the EVERYBOT Three-Spin Robot Mop. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use and retain it for future reference.

Figure 1: EVERYBOT Three-Spin Robot Mop TS300

2. What's in the Box

Verify that all components are present upon unboxing:

• EVERYBOT Three-Spin Robot Mop
• Charging Cradle
• Remote Control
• Power Adapter
• Mother-Yarn Mop Pads (for intensive mopping)
• Microfiber Mop Pads (for fine dust and polishing)
• Water Tank
• User Manual

3. Setup

3.1 Charging the Device

1. Place the charging cradle against a wall in an open area.
2. Connect the power adapter to the charging cradle and a power outlet.
3. Align the robot mop with the charging cradle. The device will automatically dock and begin charging. The battery indicator lights will illuminate.

3.2 Preparing Mop Pads

1. Select the appropriate mop pads (Mother-Yarn for intensive cleaning, Microfiber for polishing).
2. Moisten the mop pads with water and wring them thoroughly to remove excess water.
3. Attach the moistened pads to the rotating discs on the underside of the robot mop. They attach via Velcro.

3.3 Filling the Water Tank

1. Open the water tank cover located on the top of the robot mop.
2. Remove the water tank.
3. Fill the tank with clean tap water. Do not add hot water or cleaning detergents to the tank, as this may damage the device or leave residue on your floors.
4. Securely close the water tank cap and reinsert the tank into the robot mop. Close the water tank cover.

Figure 2: Water Tank Filling Guidelines

4. Operation

4.1 Powering On/Off

• To power on: Press and hold the power button on the device for approximately 3 seconds.
• To power off: Press and hold the power button for approximately 3 seconds.

4.2 Cleaning Modes

The EVERYBOT Three-Spin offers 7 selectable cleaning modes via the remote control:

• Automatic Cleaning: Basic mode for efficient room cleaning.
• Intensive Cleaning: Repeats short forward movements and 360-degree rotations for meticulous cleaning.
• Focused Cleaning: Intensively cleans the nearby area based on the robot's current location.
• Edge Cleaning: Directs the robot along walls and furniture edges.
• 50-minute Cleaning: Cleans for a set duration, suitable for separate rooms.
• Y-Mode Cleaning: Follows a Y-shaped pattern for thorough coverage.
• Manual Cleaning: Allows direct control of the robot's movement using the remote.

Figure 3: Remote Control for Mode Selection

Figure 4: Visual Representation of Cleaning Modes

4.3 Smart Features

• Ultra Quiet Operation: Operates at an ultra-low 43 dB noise level.
• No-Wheel Structure: The 4.4 lb weight provides direct pressure for effective cleaning.
• Smart Sensors: Equipped with 11 anti-collision and fall prevention sensors to navigate safely and avoid obstacles or drops.
• Automatic Water Supply: The 300ml water tank automatically supplies water to the mops to maintain dampness.

Figure 5: Quiet Operation (43 dB)

Figure 6: Obstacle Avoidance with Smart Sensors

5. Maintenance

5.1 Cleaning Mop Pads

After each use, remove the mop pads. They can be hand-washed with water or machine-washed according to their care instructions. Ensure they are clean and dry before reattaching.

5.2 Cleaning Sensors

Periodically wipe the 11 anti-collision and fall prevention sensors with a soft, dry cloth to ensure optimal performance.

5.3 Water Tank Care

Empty any remaining water from the tank after each use. Clean the tank regularly with water to prevent buildup. Do not use harsh chemicals.

6. Troubleshooting Guide

If the red light flashes and error sounds persist, try the following steps:

1. Power Off: Press the power switch for more than 3 seconds to turn off the device.
2. Sensor Management: Remove any plastic film attached to the sensors. If there is dust or debris on the sensor, gently wipe it with a soft cloth.
3. Attach Mop Properly: Moisten the mop in water and wring it thoroughly. Attach the mop to the rotating disc slot. If the mop is too wet or not properly attached, the product may not operate correctly.

7. Specifications

8. Product Videos

9. Warranty and Support

For warranty information, technical support, or to purchase replacement parts, please refer to the official EVERYBOT website or contact customer service. Keep your purchase receipt for warranty claims.