Introduction
This manual provides essential instructions for the safe and efficient operation of your GP ReCyko E211 2-Slot USB Battery Charger. Please read this manual thoroughly before use and retain it for future reference.
The GP ReCyko E211 charger is designed for charging Nickel-Metal Hydride (NiMH) rechargeable batteries. It features intelligent charging capabilities to detect non-rechargeable, damaged, or partially charged batteries, optimizing the charging process and preventing overcharging.
Safety Information
- Use only with NiMH rechargeable batteries. Do not attempt to charge alkaline, carbon-zinc, or other battery types.
- Do not disassemble, modify, or short-circuit the charger or batteries.
- Keep the charger and batteries away from water, moisture, and extreme temperatures.
- Ensure proper battery polarity (+/-) when inserting batteries into the charger. Incorrect insertion will prevent charging.
- Unplug the charger from the power source when not in use or before cleaning.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Package Contents
- 1 x GP ReCyko E211 USB Battery Charger
- 2 x AA 2100mAh NiMH Rechargeable Batteries
Setup
Connecting the Charger
- Locate a suitable USB power source (e.g., computer USB port, USB wall adapter, power bank).
- Connect the USB cable (integrated or supplied) from the charger to the USB power source.
- The charger is now ready for use.
Image: GP ReCyko E211 charger and two AA batteries in their retail packaging. The charger is white with two green AA batteries inserted, indicating it's ready for use or charging.
Operating Instructions
Inserting Batteries
- Ensure the charger is connected to a power source.
- Insert 1 or 2 AA or AAA NiMH rechargeable batteries into the charging slots. Observe the correct polarity (+/-) as indicated on the charger.
- The charger is designed to charge batteries in pairs. If only one battery is inserted, charging may not initiate.
Image: A close-up view of the GP ReCyko E211 charger with two green AA rechargeable batteries correctly inserted into the charging slots. The positive and negative terminals are clearly visible.
Charging Process
- Once batteries are correctly inserted and the charger is powered, the charging indicator light(s) will illuminate.
- The charger automatically detects the battery status (non-rechargeable, damaged, or partially charged) and adjusts the charging speed.
- Charging typically takes approximately 8 hours for the included 2100mAh AA batteries.
- Upon completion of charging, the charger will switch to a maintenance charging mode to prevent overcharging and prolong battery life.
Charging Indicators
Refer to the LED indicator on the charger for status:
- Solid Green LED: Batteries are charging.
- No LED / Off: No batteries inserted, batteries incorrectly inserted, or charging complete and charger is in standby/maintenance mode.
- Flashing LED: Indicates an error, such as non-rechargeable or damaged batteries, or incorrect battery type.
Maintenance
- Cleaning: Disconnect the charger from the power source before cleaning. Use a dry, soft cloth to wipe the exterior. Do not use liquid cleaners or solvents.
- Storage: Store the charger and batteries in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: For optimal battery life, avoid fully discharging NiMH batteries before recharging. It is recommended to recharge them when they are partially depleted.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger LED does not light up. | No power connection, batteries incorrectly inserted, or non-rechargeable/damaged batteries. | Check USB power connection. Re-insert batteries with correct polarity. Ensure batteries are NiMH and not damaged. |
| Batteries not charging. | Incorrect battery type, damaged batteries, or only one battery inserted (charger requires two for charging). | Ensure batteries are NiMH. Replace damaged batteries. Insert two batteries for charging. |
| Charging takes longer than expected. | Batteries have higher capacity, or power source provides lower current. | This is normal for higher capacity batteries. Ensure USB power source provides sufficient current (e.g., 1A or higher). |
Specifications
- Model: GP ReCyko E211 (Part Number: 420.10.60.0003)
- Input: USB (Voltage: 5V, Current: 1A recommended)
- Output: 1.2V (for AA/AAA NiMH batteries)
- Charging Slots: 2 (for AA or AAA batteries)
- Typical Charging Time: Approximately 8 hours for 2100mAh AA batteries
- Dimensions: 8 x 5 x 10 cm
- Weight: 60 g
- Included Batteries: 2 x AA 2100mAh NiMH Rechargeable Batteries
Warranty and Support
For warranty information and customer support, please refer to the documentation provided with your purchase or visit the official GP ReCyko website. Keep your proof of purchase for warranty claims.
Manufacturer: GP ReCyko